[FS] Euro mx3 breaking

[marcdh]

Sill collapsed jacking it up to replace trailing arm Underside is officially iron oxide.



PHOTO ALBUM OF PARTS, will be added to as they come off:
http://s49.photobucket.com/albums/f295/marcdh/breaking/

Parts:



Doors are in good condition £25 each (UK only due to postage extortion)

Wing mirrors £12 a side

Rear hatch and glass £40 (UK only due to postage extortion)

Rear bumper, very good condition, was pro resprayed a few years ago £50 (UK only due to postage extortion)

Front bumper, reasonable condition £30 (UK only due to postage extortion)

Bonnet good condition, but stone chipped as you'd expect £40 (UK only due to postage extortion)

Gearbox £50 or £100 with taller 5th gear to drop revs by 6-700rpm for cruising mpg and higher top speed
Can sell taller 5th for £50 separately if there's interest

As new Exedy/Daiken/OEM pressure plate £40

Exedy clutch Disc (had to clean up the splines) £20

Skimmed KF01 flywheel 16.8lbs (always reskim flywheel before new clutch!) Machining cost £30, used for half a mile, yours with new high quality pilot bearing for £45

-40mm lowering springs, only about 12k on these £55

Rear brake calipers, about 15k on these £25 a side

1.8 ECU, quite possibly chippable, will check £30

JE50 VAF £20

ABS Computer £20

ABS Sensors £10 a corner

Rear wheel bearings £30 a side

Rear spoiler, rattle can respray £20

Alternator £25

Glass Headlights £20 a side, can remove and just ship glass to save postage
http://i49.photobucket.com/albums/f295/ ... G_0752.jpg
http://i49.photobucket.com/albums/f295/ ... G_0753.jpg

Euro bumper support £15



Seats £50 for the lot

Euro Sliders, one mounting tab damaged, other 5 intact so will still be stable £15
http://i49.photobucket.com/albums/f295/ ... 28a6cb.jpg
http://i49.photobucket.com/albums/f295/ ... 376a73.jpg

Usual other parts available. I can take photos upon request.


SOLD with thanks:
Euro tow hook to Daninski
4x Bilstein Shocks to Hammy
Stainless cat back to Hammy
Mini euro side skirts to stangant

[Josh]

Sad, such a nice car on the outside.

PM sent!

[Daninski]

Too bad it is a nice clean looking MX-3
Dibs on Tow Hook? Shipped to KOK 1Y6 in Ontario Canada. I have PayPal. Thanks

[MrMazda92]

It's a crying shame I wish you could fix it, but car-cancer is a tough choice for most of us...

How much would shipping be on the front bumper support to 97402, USA?

Thank you very much.

[marcdh]

Thanks guys. Pretty gutted, but as I strip I see more and more rust. Definitely the right call. I'll reply to PMs etc tomorrow hopefully.

Some pics so far:

[AaronTietje]

Hi, I'm interested in the front bumper support with fog light brackets and fog lights and................any fog light wire harness.

Thanks a ton,
Aaron


Pm me a total price shipped to NY state.

[DeepBlueMX3]

Do you have door stainless steel sills?
If you do I'm interested, pics?

[marcdh]

Yes Aaron, and PM'd

Not on this car, sorry!

[AaronTietje]

Yes Aaron, and PM'd


I didn't get the pm

[MrMazda92]

I'm still waiting for a quote on the bumper support as well.

[marcdh]

Sorry guys, many excuses, work, college, working weekends and the online price finder being broken for days etc

Currently Josh has first refusal on the front bumper support and rear bumper cover.

FYI though:

I'm still waiting for a quote on the bumper support as well.

Last time I shipped to Wyt it was:
approx £50 for surface mail (up to 8 weeks)
approx £60 for airmail (less than 7 days)

And then £20 for the actual part and packaging (took me an hour to wrap last time!)

However the online calculator is down on Royal Mail and Parcel Force at the moment. It's probably gone up a bit since then

Yes Aaron, and PM'd
I didn't get the pm

Sorry Aaron, wrong person! You can have the fogs, brackets, and some harness from the front, but currently Josh has first dibs on the support. I'll check their condition and photograph tonight if you like. Price for fogs, brackets, and some harness from the front will be no more than £25 plus post and probably less depending on condition.

[marcdh]

Clutch bits added:

As new throw out /clutch release bearing, genuine mazda part £25

As new Exedy/Daiken/OEM pressure plate £40

Exedy clutch Disc (had to clean up the splines) £20

Skimmed KF01 flywheel 16.8lbs- Machining cost £30, used for half a mile, yours with new high quality pilot bearing for £45

[Sleeper6]

If I have some funds left over after the holidays I might bug you about that rear bumper...

[projectmx]

If the first buyer for the bumper backs out let me know!

[mx-3_4evr]

I'm next on the whole front bumper assembly!