[Fs] JDM front End
-
- Regular Member
- Posts: 158
- Joined: December 1st, 2005, 4:20 am
- Location: Winnipeg, Manitoba , Canada
[Fs] JDM front End
For sale is one jdm front end. It is used and is from a 94 mx3. I will be using a MS front end instead so i don't need this. I don;t know how much to ask so i will update later.
*note* bumber is scuffed alot on the lip so it will need to be painted. and has a dent. Bumper is not cracked though.
*note* bumber is scuffed alot on the lip so it will need to be painted. and has a dent. Bumper is not cracked though.
- Limegreen mx-3
- Regular Member
- Posts: 1778
- Joined: October 29th, 2002, 2:01 am
- Location: San Antonio TX
- Contact:
Interested.
(12.4@118@18psi) 92 MX-3, KIA (BP-DE)Swap, Electromotive TEC II Standalone, 8,200 Rev Limit, Custom Intake/Exhaust Manifold, 1,000cc PTE Injectors, Custom Fuel Rail, Aeromotive FPR, 80MM Holley TB, MSD 8.5MM Wires, NGK V-Power #8, SC6262 Turbo, 3 in. DownPipe, Tial WG/BOV, 600HP PTE FMIC, 2.5IN Intercooler Piping, EQUUS/Autometer KIA G-Series Tran, Extreme ACT Clutch, Built BP in starting process.
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
interested as well, how much shipped to spokane, WA 99207
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
might lower price, since it needs bodywork
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
looks spiffy wish i had the cash on hand dude How does it look with the hood though?????
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
whatcha mean.., same way it would look wihtout it, the bumper is upside down in the pic .. if thats what you mentMechaManZero wrote:looks spiffy wish i had the cash on hand dude How does it look with the hood though?????
93 323- BP swap,Pacesetter header,magnaflow,highflow cat, pacesetter catback,Rx7vaf+filter, Adv timing, Fidanza Adj camgears, GTx front bumper, EGT side skirts, Espec headlights, LED upper spoiler, GTR midwing, familia rear garnish, Mx3 carpet +all seats,
92-mx3 gs
92-mx3 gs
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
oh lol. du du duh. lmao. hahaha. I was like hmmmmm is the blinkers on the bottom. That looks pretty cool ha.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- jschrauwen
- Forum Moderator
- Posts: 6052
- Joined: September 27th, 2003, 2:01 am
- Location: Frankford, Ontario, Canada
- Contact:
Someone scoop this up, you'll never regret it. Of course I'm a little bisaed when it comes to these front ends .... LOL. Focal, you should mention if it comes with the J-Spec rebar and fog lights too.
'92 GS-ZE - sold, '95 GS - sold, '02 Protege LX - Daughter, '00 Audi A4 2.8 QTip, Ducati TT2
90 JDM RHD 300ZX TT - 572.1 RWHP | 590.0 RWTQ | 21 PSI | Pump gas
90 JDM RHD 300ZX TT - 572.1 RWHP | 590.0 RWTQ | 21 PSI | Pump gas