mazda motors for mx-3
Posted: September 17th, 2003, 12:38 am
what would be the fastest motor to put in my 4cyl mx-3?
MX-3.com
The Worlds First and Largest Mazda MX-3 Forums
https://mx-3.com/phpbb3/
mazda motors for mx-3
Page 1 of 2
Re: mazda motors for mx-3
Posted: September 17th, 2003, 1:10 am
It really depends. Do some research on different engines and the answer will come to you.
Re: mazda motors for mx-3
Posted: September 17th, 2003, 10:38 pm
Sorry Guys.. What i meant was whats the fastest motor to date in an RS?<p>[ September 17, 2003: Message edited by: ALLSPEED GiNO ]</p>
Re: mazda motors for mx-3
Posted: September 19th, 2003, 8:15 pm
bp or bpt
Re: mazda motors for mx-3
Posted: September 19th, 2003, 9:43 pm
11.2~ dave lazier methonal
Re: mazda motors for mx-3
Posted: September 19th, 2003, 9:46 pm
he no longer has that car. it was the fastest to date fwd mx-3.
Re: mazda motors for mx-3
Posted: September 22nd, 2003, 12:20 pm
where did it go!! i havent found any new news on him.
Re: mazda motors for mx-3
Posted: September 22nd, 2003, 5:25 pm
Re: mazda motors for mx-3
Posted: September 22nd, 2003, 6:41 pm
Dave sold it but the guy that owns it now has a different set up. I think it was Darren that talked to the knew owner and said he was a grumpy old man. Darren, any other news?
Re: mazda motors for mx-3
Posted: January 1st, 2004, 7:26 pm
To mx3TT,
I'm the grumpy old man.
Before to carry a judgment,do you know me??
I drag only for my pleasure and beat my times in
the last 3 years.I never go in any race until
10-14-03 at Nappi.
I run my best ever:
11.28@ 125
The only thing that i change in the motor(1.8 bp) are the rods from a b6t 88 (Bigger)
The motor run great until 9000 RPM
The turbo is a Garrett GT 35-40R at 18 lbs
Inj 96 lbs 1000 cc
Stand alone Advance EFI
Header, piping ect custom by ME
I break 2 jack shaft and 2 axles (stock)
The car run on a street(2000 kms) this summer
Winter project:
New motor ( forged)
New tranny (626 turbo 89) custom fit and axles
Hope for low 10
PLEASURE TO SEE YOU ON A TRACK NEXT SUMMER
DRAG323
Eric
I'm the grumpy old man.
Before to carry a judgment,do you know me??
I drag only for my pleasure and beat my times in
the last 3 years.I never go in any race until
10-14-03 at Nappi.
I run my best ever:
11.28@ 125
The only thing that i change in the motor(1.8 bp) are the rods from a b6t 88 (Bigger)
The motor run great until 9000 RPM
The turbo is a Garrett GT 35-40R at 18 lbs
Inj 96 lbs 1000 cc
Stand alone Advance EFI
Header, piping ect custom by ME
I break 2 jack shaft and 2 axles (stock)
The car run on a street(2000 kms) this summer
Winter project:
New motor ( forged)
New tranny (626 turbo 89) custom fit and axles
Hope for low 10
PLEASURE TO SEE YOU ON A TRACK NEXT SUMMER
DRAG323
Eric
Re: mazda motors for mx-3
Posted: January 3rd, 2004, 3:07 pm
we are sorry, u seem quite pleasent 
Re: mazda motors for mx-3
Posted: January 3rd, 2004, 3:23 pm
sounds pretty grumpy to me
Re: mazda motors for mx-3
Posted: January 4th, 2004, 12:13 am
I never said you were grumpy...read it again.
Re: mazda motors for mx-3
Posted: January 4th, 2004, 12:24 am
I know Dave.. We talk a lot over the net..
The Car chassis, the engine, and the transmission were sold separetly..
BoostedMx own the tranny..
the shell went to someone in gatineau.. so, yeah, Drag323 might be the owner, and the engine, was told it went in NewYork.. Gotta find my record of the conversation..
I was suppose to buy the motor.. just a question of hours for the deposit..
The Car chassis, the engine, and the transmission were sold separetly..
BoostedMx own the tranny..
the shell went to someone in gatineau.. so, yeah, Drag323 might be the owner, and the engine, was told it went in NewYork.. Gotta find my record of the conversation..
I was suppose to buy the motor.. just a question of hours for the deposit..
Re: mazda motors for mx-3
Posted: January 4th, 2004, 5:08 am
didnt someone fit a 13b into a mx-3....theni think that would be the fastest mx-3