Page 3 of 4

Re: mazda 323 v6

Posted: May 8th, 2008, 1:02 pm
by fowljesse
Cool. I'm glad, and hope he does make a worklog. I'd also like to see the dyno, to see where the powerband is and if it's shorter.

Re: mazda 323 v6

Posted: May 8th, 2008, 7:51 pm
by leo323
getfuelinjected.com thats the link for the electromotive iff you whant you can get some info there

it uses a gm mafsensor and it has a crank sensor for the pick up very simple ill take pictures later and post them

Re: mazda 323 v6

Posted: May 10th, 2008, 10:29 pm
by fowljesse
Thanks, Leo. We would love to see as many pictures, and as much information as you'd like to show.

Re: mazda 323 v6

Posted: May 13th, 2008, 8:09 pm
by leo323
this are my new down pipes hope you like them


Image

Image

Image

Image


Image

Image

Re: mazda 323 v6

Posted: May 13th, 2008, 9:12 pm
by Ryan
This car is sweet and all, and I hate to say this, but isn't this MX-3.com? I suppose it is a very similar engine bay....

Re: mazda 323 v6

Posted: May 13th, 2008, 9:15 pm
by Savin
But it is also a place for engines like ours. Isn't this a K-series engine? If so, then it applies and can help out you V6 guys. :mrgreen:

Re: mazda 323 v6

Posted: May 14th, 2008, 1:35 pm
by leo323
the engine bay of a mazda 323 is the same engine bay as the mazda mx3 and yes my engine is a k series thats Y posted some photos and some info of my car I know this is a mx3 forum i know how to read I havent had this kind ov problems in the other forums yust triing to help you guys thanks for the suport

Re: mazda 323 v6

Posted: May 14th, 2008, 1:57 pm
by fowljesse
Thanks, LEO! That's nice work! I wish I could do that. What are you doing for a flex pipe?
The only difference in this thread is the front clip. These pictures, and whatever else gets put up will help alot of MX-3ers.

Re: mazda 323 v6

Posted: May 14th, 2008, 3:27 pm
by Dali
thats some good work. the 323 and mx3 have the same chassis, ive swapped over the sub frames, harness, motor, tranny, exhaust and most of the interior from my special edition over to the 323. the only things i left in the 323 are door panels, heater core, fuel tank, brake and fuel lines.

Re: mazda 323 v6

Posted: May 14th, 2008, 3:34 pm
by wytbishop
I love your project Leo. I would love a more detailed description of your ITB setup as well as your ignition system.

Re: mazda 323 v6

Posted: May 15th, 2008, 1:17 am
by leo323
my ingnition sistem is controled by the programable electromotive tec 3 computer
here are my new dyno numbers whent to the dyno today

Image

Re: mazda 323 v6

Posted: May 16th, 2008, 3:10 am
by hgallegos915
If I would find a 323, I would COMPLETELY swap my set up and junk my mx3! lol for reals :)

Re: mazda 323 v6

Posted: May 16th, 2008, 5:21 am
by marcdh
hgallegos915 wrote:If I would find a 323, I would COMPLETELY swap my set up and junk my mx3! lol for reals :)
yea?! I think 323s are legendary but mx3s are sex. I like a car that can't be drawn with 4 lines and a ruler :lol:
._____
/..........\__
|_0____0_|

(ok maybe 7)

Re: mazda 323 v6

Posted: May 16th, 2008, 11:55 am
by leo323
lol thats funny

Re: mazda 323 v6

Posted: May 19th, 2008, 1:15 am
by hgallegos915
but here 323s are VERY RARE

. Id love to find a shell , slap my set up.. and run low low 14s