MX-3.com

looks like just the piping and the filter you need the adapters for it. but that website is a ripe off they over charge there stuff so much!

but i am going to get me one of those shift knobs tho.

yea those are sick i havent seen them anywere else im definetly gonna order one

with these intakes you have to watch out for water. Plus i am still wondering if it comes with the air filter or not.... it doesnt say. But in my case i would wrather go to a PRM or a weapon-r intake. The weapon-r intakes are really nice intakes becuase they are so easy to clean and they give the most HP gain then any other intake. Because how its made you can read mroe about it at http://www.weapon-r.com.

i personally think the weapon r intake 'secret weapon or whatever' is possibly the worst 190bucks ive ever spent. for those who dont know. u dont get what the picture shows. u literally get a filter, and clamps, and a short 90degree pipe....it makes the motor sound sweet as hell, but def. not worth 190bucks....autzone sells a filter and then sells a 90degree pipe for like 40bucks so.....

witht he weapon r its the filter they are the first company i see to have a filter liek that its not a cotten filter like the rest are its like fome its realy easy to clean. Its a realy pain int he a-- to clean a cotten filter. But its up to you one what to get. I like my PRM because the cone is inclosed so no hot air gets in.

the weapon r is nothing BUT hot air....and the picture they show u to make u think ur getting, is equivilant to a cold air intake setup, when ur really just gettin a very short 90degree pipe

Legato626 wrote:witht he weapon r its the filter they are the first company i see to have a filter liek that its not a cotten filter like the rest are its like fome its realy easy to clean. Its a realy pain int he a-- to clean a cotten filter. But its up to you one what to get. I like my PRM because the cone is inclosed so no hot air gets in.

i'm confused ur saying because ur filter is in the inside of the intake that ur car wont suck up hot air, doesnt the placement of the end of the intake where its sucking air from depend on that not where the filter is??

jschrauwen wrote:Brno, CZ ?? Have you been on the race track there yet? Seen any good GP's?

Sure I was, it's opened for about 10 years. I don't like MotoGP so much and entrance is pretty high but yes, I saw there som ereally good races - GTs etc.
To my question, I know some questions are already answered in another posts but BB is not so precise in searching I could use. More to that, the search result shows you only topic, not exact post and when there's 20 pages of one topic, you should spend hours of reading you never wanted.
My question was simple, if I could use the one-piece set of CAI from Integra 90-93 or do I have to put it back and let reimburse money back and buy the two-pieces one. This is exact question which could be answered by few words. Thanks

robinek wrote:

jschrauwen wrote:Brno, CZ ?? Have you been on the race track there yet? Seen any good GP's?

Sure I was, it's opened for about 10 years. I don't like MotoGP so much and entrance is pretty high but yes, I saw there som ereally good races - GTs etc.
To my question, I know some questions are already answered in another posts but BB is not so precise in searching I could use. More to that, the search result shows you only topic, not exact post and when there's 20 pages of one topic, you should spend hours of reading you never wanted.
My question was simple, if I could use the one-piece set of CAI from Integra 90-93 or do I have to put it back and let reimburse money back and buy the two-pieces one. This is exact question which could be answered by few words. Thanks

I believe someone just mentioned that they too got the Integra one piece unit and were going to keep it because it had enough of a run and enough of the correct angled bends to adequately cut down to fit our needs. It may meean an extra cut or 2 but that's quite easy with the aluminum. The 2 piece units have to be cut down anyway to meet our needs. So, yes it should meet your needs if you take a look at the pics I've provided and the bends in the tubing necessary to work for us.

jschrauwen wrote:I believe someone just mentioned that they too got the Integra one piece unit and were going to keep it because it had enough of a run and enough of the correct angled bends to adequately cut down to fit our needs. It may meean an extra cut or 2 but that's quite easy with the aluminum. The 2 piece units have to be cut down anyway to meet our needs. So, yes it should meet your needs if you take a look at the pics I've provided and the bends in the tubing necessary to work for us.

Thank you, that's what I wanted to get as answer. I was offered to return the CAI and refund money OR to get $15 off so now it's clear how to decide.

The one piece intake works fine. I just made mine a couple weeks ago and i love it. Take a look at my link, hopefully it will help you out. http://mx-3.com/phpbb2/viewtopic.php?t=46225