Any one who has replaced clutch pls help
-
Savin
- Regular Member
- Posts: 1580
- Joined: November 18th, 2007, 3:05 pm
- Location: Crown Point, IN (Chicago area)
- Contact:
Re: Any one who has replaced clutch pls help
Moons, I'm not sure breaking your nuts is a good thing
'95 MX-3 RS - Project "Déjà Vu" Destined for the scrapyard.
'93 MX-3 GS - SOLD!
'93 MX-3 GS SE - Parts car!
'94 MX-3 GS - Scrapped
'94 MX-3 RS - Scrapped
'96 Sunfire SE - Scrapped
'03 Sunfire SE - Deathtrap
'95 Cavalier Base - Scrapped
'94 Thunderbird LX - Collects dust
'89 Mustang GT - SOLD!
'93 MX-3 GS - SOLD!
'93 MX-3 GS SE - Parts car!
'94 MX-3 GS - Scrapped
'94 MX-3 RS - Scrapped
'96 Sunfire SE - Scrapped
'03 Sunfire SE - Deathtrap
'95 Cavalier Base - Scrapped
'94 Thunderbird LX - Collects dust
'89 Mustang GT - SOLD!
-
marcdh
- Regular Member
- Posts: 1460
- Joined: July 26th, 2006, 3:54 pm
- Location: Belfast -Northern Ireland
- Contact:
Re: Any one who has replaced clutch pls help
my air impact wrench failed at this, it's hardly low spec either. I got my brother to hold the brakes and I used a breaker bar with 6' scaffolding I've also tried using a car jack under the end of the breaker bar, which failed too. My car was lifting up before the bolts broke loose 
Make sure to undent the notch too. I also melted wax into the threads, may or may not have helped...was desparate!
I've also tried using a car jack under the end of the breaker bar, which failed too. My car was lifting up before the bolts broke loose Make sure to undent the notch too. I also melted wax into the threads, may or may not have helped...was desparate!AZ-3 1498cc Turbo! EVO 8 turbo and manifold, 5 stud swap, SSR Type C, DIYPNP seq Megasquirt
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
-
Ryan
- Senior Member
- Posts: 7198
- Joined: April 7th, 2008, 1:06 pm
- antispam: ~SPAM*SUX~
- Location: Manitoba
Re: Any one who has replaced clutch pls help
Penetrating Oil, WD40... and if you can't crack it with an air gun or a 6' torque bar, its probably welded on 
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
-
ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Re: Any one who has replaced clutch pls help
My drivers side one was stuck, so i just took the whole strut and hub out. Not much harder than spending an afternoon screwing around with that damn stuck nut.
KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)