HEADER QUESTION
-
- Regular Member
- Posts: 57
- Joined: October 29th, 2003, 2:01 am
- Location: ST.GEORGE, UTAH
HEADER QUESTION
I READ ABOUT HOW SOMEONE TOOK THE HEADER FOR THE PROBE 4CLYD AND MADE IT FIT THE DOHC I WAS WONDERING IF YOU COULD DO THE SAME FOR THE SOHC
Re: HEADER QUESTION
First off, dude lay off the caps i dont care if your blind and you cant read. I would rather see it misspelled than in caps.
USe the search functoin this has been touched on a lot before. The SOHC is too diffrent i belive btw.
USe the search functoin this has been touched on a lot before. The SOHC is too diffrent i belive btw.
-torp.
I don't own a Mazda.
I don't own a Mazda.
-
- Regular Member
- Posts: 57
- Joined: October 29th, 2003, 2:01 am
- Location: ST.GEORGE, UTAH
Re: HEADER QUESTION
sorry about the caps but know one answerd my question will the probe header work for the sohc like it did for the dohc
Re: HEADER QUESTION
Originally posted by torpedan:
The SOHC is too diffrent i belive btw.
-torp.
I don't own a Mazda.
I don't own a Mazda.
Re: HEADER QUESTION
what I did was: I got a brand new ractive 4-2-1 headers for the honda b16, went to a exhaust house and they custom made a flange of the original headers, then welded to the ractive headers and VOILA; imediate power.
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: HEADER QUESTION
good idea
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
-
- Regular Member
- Posts: 57
- Joined: October 29th, 2003, 2:01 am
- Location: ST.GEORGE, UTAH
Re: HEADER QUESTION
pics???
how much did it cost
how much did it cost
Re: HEADER QUESTION
ractive stainless steel 4-2-1 about 300 dollars plus 125 dollars for the custom flange plus 50 for weldings and assembly. Ill try show pics of all my mx. I know Its expensive but the power gain is pretty good.