I need to sell engine and transmission first before anything else will be sold.
Engine: defintely has less than 5k miles on it. Id actually say 2-3k. Other than what is listed below the engine is also set up with a miata distributorless ignition and coil packs.
Japan Spec B6T Block
Japan Spec B6T Rods
Mazdaspeed cam gears
Wiseco 1MM overbore forged and coated pistons
Fully bananced internals
B6DE raceported head
1mm stainless steel oversized valves
heavy duty valve springs
Custom 256 grind stage 2 turbo cams
cometic head gasket
arp head studs
Everything listed above I would get rid of for $2500. I know thats a HELL of a deal for the items listed above. I have that much just wrapped up in the block prep and head.
Transmission:
Has the same amount of mileage as the engine. It was taken out of a 26k mile protege that was rear ended. Built by Corksport and the fifth gear was changed to get a bit better rpm range on the freeway. It has a mazdaspeed LSD installed The ACT clutch is a hybrid of mx3 and protege parts. The driveshafts MUST go with due to their custom manufacture. The jackshaft is deleted and the car definitely still pulls straight. Id ask $2500 for the transmission as well.
Shipping is negotiable....Id rather not ship but I know im in the northwest. Shipping would be from 97201
[GI] Partout of my beloved MX3
- cjthor
- Forum Moderator
- Posts: 5018
- Joined: November 26th, 2000, 2:01 am
- Location: Portland Oregon
- Contact:
Re: [GI] Partout of my beloved MX3
Jarid Perry
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
- Josh
- Supporting Member
- Posts: 3432
- Joined: April 18th, 2002, 2:01 am
- Location: Washington state
- Contact:
Re: [GI] Partout of my beloved MX3
Hey if you are really serious post this on the 323, festiva, and Club protege forums. you might have a lot more interest for the engine trans set up.
Josh
95' AWD MX-3 RST - (work log - http://www.mx-3.com/phpBB3/viewtopic.php?f=46&t=73765 )
94' GS - KLZE DD (work log - viewtopic.php?uid=2713&f=46&t=79063&start=0 )
05' MS RX-8 - Parted out and Sold :'(
Feedback - http://www.mx-3.com/phpBB3/viewtopic.php?f=37&t=49519
Cardomain Page - http://www.cardomain.com/ride/408020
Face Book page http://www.facebook.com/pages/Mazda-MX- ... 3472959216
95' AWD MX-3 RST - (work log - http://www.mx-3.com/phpBB3/viewtopic.php?f=46&t=73765 )
94' GS - KLZE DD (work log - viewtopic.php?uid=2713&f=46&t=79063&start=0 )
05' MS RX-8 - Parted out and Sold :'(
Feedback - http://www.mx-3.com/phpBB3/viewtopic.php?f=37&t=49519
Cardomain Page - http://www.cardomain.com/ride/408020
Face Book page http://www.facebook.com/pages/Mazda-MX- ... 3472959216
- cjthor
- Forum Moderator
- Posts: 5018
- Joined: November 26th, 2000, 2:01 am
- Location: Portland Oregon
- Contact:
Re: [GI] Partout of my beloved MX3
I'm not a member of either. Id hate to troll it up and my first post is selling parts. Could you link it for me?Josh wrote:Hey if you are really serious post this on the 323, festiva, and Club protege forums. you might have a lot more interest for the engine trans set up.
Jarid Perry
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
Re: [GI] Partout of my beloved MX3
GL Jarid and send me one of those new JCWs when you get a minute, Thanks
What was the final HP of that motor?
Post some prices so I can buy a piece of your work to keep it alive.
What was the final HP of that motor?
Post some prices so I can buy a piece of your work to keep it alive.
ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
- cjthor
- Forum Moderator
- Posts: 5018
- Joined: November 26th, 2000, 2:01 am
- Location: Portland Oregon
- Contact:
Re: [GI] Partout of my beloved MX3
Until I sell the engine/transmission its not a part out...i think imma relist this.
Jarid Perry
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
- cjthor
- Forum Moderator
- Posts: 5018
- Joined: November 26th, 2000, 2:01 am
- Location: Portland Oregon
- Contact:
Re: [GI] Partout of my beloved MX3
PICS ARE BACK UP AND WORKING! TAKE A LOOK!
Jarid Perry
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S
94 mx3 Turrrbooooo (not even close to stock) 302WHP
71 Chevy C20 (tow rig!!)
77 Jeep CJ5 (no way its stock)
06 MINI Cooper S JCW GP (few goodies) 210WHP
2008 MINI Cooper Clubman S