help!!! i have coil overs :P am i doing this right
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
help!!! i have coil overs :P am i doing this right
this is what i got .. is this right idk please someone help
Last edited by cricketol2 on August 14th, 2009, 5:09 pm, edited 2 times in total.
Re: help!!! i have coil overs :P am i doing this right
Sorry I gotta say it, your bedspread looks like the exterior of a honda. I'm thinking that the second nut should also be threaded up, to lock the other in place.
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
Re: help!!! i have coil overs :P am i doing this right
but is the coils adjuster in the right place thats what i would like to know
p.s. i dont have the other parts and im not going to take it all apart just to find out that i f*^(ed up ..
p.s. i dont have the other parts and im not going to take it all apart just to find out that i f*^(ed up ..
- RS_OBD'oh_2
- Senior Member
- Posts: 2400
- Joined: April 9th, 2007, 1:26 pm
- Location: Calgary, AB
Re: help!!! i have coil overs :P am i doing this right
Hold on. I would think that the coils should be sitting damn nearn on the strut. They should come with O-rings that should fit between the coil and the outside dia of the strut. I don't think they fit low enough. Do they come with set screws?
if this is how they are seated and work that way, may not like the ride qualtiy. They look a little cheap with out progressive spring rates.
I say that they don't fit your struts.
if this is how they are seated and work that way, may not like the ride qualtiy. They look a little cheap with out progressive spring rates.
I say that they don't fit your struts.
Re: help!!! i have coil overs :P am i doing this right
How low do you want to go? Are those the ebay coil-overs?
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
Re: help!!! i have coil overs :P am i doing this right
so they dont fit the strut.. and they came with o-rings but it told me to just put it on the strut.. im now at this.. so idk where in the strut it would go i have a bag full of them..
and for how low they sit idk did not put them on yet.. i dont want to f*&^ sh!~ up so i want to know how to really put them on so i dont brake things
and for how low they sit idk did not put them on yet.. i dont want to f*&^ sh!~ up so i want to know how to really put them on so i dont brake things
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
Re: help!!! i have coil overs :P am i doing this right
yes there the ebay coil overs.. they told me that the may fit the tokico hp but i dont know if they do know .. my have to go machine a part to have the coil adjuster more less sit on the spring base what do you think about that ..
- RS_OBD'oh_2
- Senior Member
- Posts: 2400
- Joined: April 9th, 2007, 1:26 pm
- Location: Calgary, AB
Re: help!!! i have coil overs :P am i doing this right
the coil collar should be sitting around the blue section of your struts... I don't think the aluminum collars can handle the wieght of the car and would probably split. There must be lots of play in the collar.
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
Re: help!!! i have coil overs :P am i doing this right
i was board and tried them on my stock struts and they fit them not the ph..... not to happy /:( well back to the drawing board ... so are lowing springs well not compressed on the strut i got them on ebay as well.. they fit but they are loose on the strut ??
the dropzone are a 1.8 idk what that means? but so you know ..
this is the ebay url
http://cgi.ebay.com/ebaymotors/NEW-Drop ... ccessories" onclick="window.open(this.href);return false;
the dropzone are a 1.8 idk what that means? but so you know ..
this is the ebay url
http://cgi.ebay.com/ebaymotors/NEW-Drop ... ccessories" onclick="window.open(this.href);return false;
Last edited by cricketol2 on August 14th, 2009, 7:49 pm, edited 3 times in total.
- RS_OBD'oh_2
- Senior Member
- Posts: 2400
- Joined: April 9th, 2007, 1:26 pm
- Location: Calgary, AB
Re: help!!! i have coil overs :P am i doing this right
pics may help.. But you should need a spring compressor to install lowering springs. I would like to suggest you just get the eibachs.. I've done the same thing you have, just to see things fail.
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
Re: help!!! i have coil overs :P am i doing this right
if things go any worst i was just going to go with .. theres
http://www.horsepowerfreaks.com/perform ... /Coilovers" onclick="window.open(this.href);return false;
Ground Control Coilovers for the MX3
http://www.horsepowerfreaks.com/perform ... /Coilovers" onclick="window.open(this.href);return false;
Ground Control Coilovers for the MX3
- RS_OBD'oh_2
- Senior Member
- Posts: 2400
- Joined: April 9th, 2007, 1:26 pm
- Location: Calgary, AB
Re: help!!! i have coil overs :P am i doing this right
they look like they might be drop zones.. they should be fine. Again.. no pregressive spring rates.
- umcamara
- Supporting Member
- Posts: 1892
- Joined: June 12th, 2007, 3:15 am
- antispam: No
- Location: Winnipeg, Manitoba, Canada
Re: help!!! i have coil overs :P am i doing this right
You don't need a spring compressor to get the rear springs on the struts, they don't really compress at all. Many people can confirm this.
-
- Regular Member
- Posts: 209
- Joined: February 10th, 2008, 9:00 am
Re: help!!! i have coil overs :P am i doing this right
ok cool thanks but when you hit a big bump does anyone have a problem?
Re: help!!! i have coil overs :P am i doing this right
my friend just got these for his crx. TAKE OUT THE ADJUSTORS! and just put the springs right on the bottom plate.cricketol2 wrote:this is what i got .. is this right idk please someone help
SOOO LOWWWW
CF Hood, Kenwood everything, 2.25 catback exhaust, H&R Springs, F&B Strut bars
My worklog: http://mx-3.com/phpBB3/viewtopic.php?f=46&t=68856" onclick="window.open(this.href);return false;
Good afternoon from the biggest Douch around;D
My worklog: http://mx-3.com/phpBB3/viewtopic.php?f=46&t=68856" onclick="window.open(this.href);return false;
Good afternoon from the biggest Douch around;D