Gauge Cluster Removal

This forum is for discussion of topics relating to MX-3 lighting such as Headlights, Tail lights, Accessory Lights, Interior Lights, Etc. For example, Rear Euro Altezza Style Tail lights, Headlight units, LED's, HID's, Bulbs, Interior lights, Neons, Strobes, Auxillary Lights/Fogs or anything filament and gas discharge related.
Also anything dealing with the elctrical system.
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Gauge Cluster Removal

Post by 93vtecklr »

Hello all, I am new to the forums and am a novice do-it-yourselfer. I would like to remove the gauge cluster so I can paint the bezel blaze red. I removed the three screws above the cluster, and the three screws for the lower panel below steering column. What I'd like to know is if there are any other screws/fasteners/clips that I am not aware of because it's not coming out and I don't want to break anything. I only want to go mild on the interior because I think the SE has a beautiful interior stock and don't want to further modify it aside from the bezel. I've browsed the forums for a while and you guys have helped me out a lot. Any insight would be great. Thanks.
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
Ryan
Senior Member
Posts: 7198
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Gauge Cluster Removal

Post by Ryan »

You have a SE?

I'll assume then that you have a digital speedometer, as apposed to cable.

The actual shroud... the top piece covering the steering column should pop off if you removed the drivers-side-most screw on the bottom. Behind that, you'll see a little rubber flap. Behind that there are two more screws. The shroud should come off at this point (I've taken my cluster out 10+ times but I'm having a brain fart) Then the screws holding the actual cluster should be apparent. Once all the screws are out, you need to pull the cluster out as far as you can, and reach behind and get all the clips. Voila. You'll need a little phillips to get the bezel off, I believe.

Hope it doesn't look tacky.

Ryan
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Re: Gauge Cluster Removal

Post by 93vtecklr »

She's an SE, and proud to say the cleanest MX-3 in the city. I'll give it a try for sure, I did notice a screw on either side of the steering column but I'll be damned I can't even fit my pinky in there. I can't even tell if those screws attach to the shroud or what.....
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
Ryan
Senior Member
Posts: 7198
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Gauge Cluster Removal

Post by Ryan »

http://www.mx-3.com/manuals/showimg.php ... /S-061.gif" onclick="window.open(this.href);return false;

should look like that, no?
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
projectzemx3
Regular Member
Posts: 1083
Joined: August 23rd, 2008, 12:09 am
Location: Beamsville.

Re: Gauge Cluster Removal

Post by projectzemx3 »

hmm im pretty good at ripping out the gauge cluster in a 94 + style dash but 92 93 is different, interesting tho.
NEED PARTS INSTALLED? PM ME!
Image
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Re: Gauge Cluster Removal

Post by 93vtecklr »

Nah, that's a 94+ diagram. But fig. 15 has those two damned screws.
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
Ryan
Senior Member
Posts: 7198
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Gauge Cluster Removal

Post by Ryan »

yes thats a 94. I thought SE's were all 94 style dash? am I crazy?
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Re: Gauge Cluster Removal

Post by 93vtecklr »

Oh god someone tell me that I actually have an SE!! '93 model, GS, black heated leather, black trim on doors, all leather cpe seats.......................Is there a VIN series to tell me for sure? I bought it off the original owner who told me it was in fact an SE.....
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
Ryan
Senior Member
Posts: 7198
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Gauge Cluster Removal

Post by Ryan »

I might be crazy. Don't worry about it. It should have "Special Edition" stickers somewhere, I just don't know where.

Some info you just don't absorb, because it doesn't apply...


http://www.mx-3.com/manuals/showimg.php ... _S-060.gif" onclick="window.open(this.href);return false;

'93
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Re: Gauge Cluster Removal

Post by 93vtecklr »

So it looks like as per that diagram fig. 9 comes apart, and I get access to that rubber flappy dealy, and those two screws can be accessed from there. Sweet! I'll give it a shot first thing in the morning, thanks a lot!
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Re: Gauge Cluster Removal

Post by 93vtecklr »

I'm about things bein clean, so as soon as I get that bezel painted and back on, I'll upload a pic for ya Ryan. I just hope it turns out the way I wanted lol.
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
Savin
Regular Member
Posts: 1580
Joined: November 18th, 2007, 3:05 pm
Location: Crown Point, IN (Chicago area)
Contact:

Re: Gauge Cluster Removal

Post by Savin »

93vtecklr wrote:Oh god someone tell me that I actually have an SE!! '93 model, GS, black heated leather, black trim on doors, all leather cpe seats.......................Is there a VIN series to tell me for sure? I bought it off the original owner who told me it was in fact an SE.....
If your car has 25th anniversary with a maple leaf on the front fenders, then it is an SE. SE's did not come with the 94+ dash. They had the 92-93 style. All leather interior/ heated seats is also a good way to tell its an SE. There were few blaze red Se's. If you do have one, keep it mint forever!
'95 MX-3 RS - Project "Déjà Vu" Destined for the scrapyard.
'93 MX-3 GS - SOLD!
'93 MX-3 GS SE - Parts car!
'94 MX-3 GS - Scrapped
'94 MX-3 RS - Scrapped
'96 Sunfire SE - Scrapped
'03 Sunfire SE - Deathtrap
'95 Cavalier Base - Scrapped
'94 Thunderbird LX - Collects dust
'89 Mustang GT - SOLD!
User avatar
93vtecklr
Regular Member
Posts: 924
Joined: March 23rd, 2009, 12:10 am
Location: Red Deer, Alberta

Re: Gauge Cluster Removal

Post by 93vtecklr »

Image
That's my girl, it was repainted so I don't know if there was any badging for that, would it be on the fender tag instead of the outside fender? Or maybe I'm not thinkin straight, oh wait, the coffees pourin.......
Image
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
User avatar
_-Night-Shade-_
Senior Member
Posts: 2664
Joined: January 15th, 2009, 8:00 pm
Location: Toronto, Ontario, Canada

Re: Gauge Cluster Removal

Post by _-Night-Shade-_ »

All SE's are 93 and therefore have the 92-93 interior. Ask Colin he did a 94+ dash swap to his SE. Also I've got a 92 with that interior (which I prefer way more than the bubble crap :P). Never removed it though cause I don't know how, I want to though, so this will come in handy for me as well lol.
--------------------------------------------
[WORKLOG] [FOR SALE] [Wishlist] [Feedback]
User avatar
Ryan
Senior Member
Posts: 7198
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Gauge Cluster Removal

Post by Ryan »

Now I know.
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Post Reply

Return to “Electrical & Lighting”