mazdamx3 website

bdr2k5 · Post by **bdr2k5** » August 7th, 2007, 10:20 pm

found this website online, some of these cats got some bad a-- mx-3's!

http://www.mazdamx-3.nl/members/member_show.php?id=128

LOVE THAT FRONT BUMPER

Princess*Precidia · Post by **Princess*Precidia** » August 9th, 2007, 10:45 am

yea theyve got some pretty sweet ride, and that is an awesome bumper..
too bad it ended up in a ditch..

Tiga · Post by **Tiga** » August 9th, 2007, 4:32 pm

That is my ride...and I am happy for me to say that the second picture isn't my car. My car is still in one piece...it hates water, so I don't think he would go for a swim.

The bumper is a NTC design H-design bumper from Germany, but I guess it will also be available in the US.

http://www.nrw-tuning-center.de/portal/ ... fault.aspx

The website mentioned in the first post is the site of the Dutch Mx-3 owners club. http://www.mazdamx-3.nl/

turbulence23 · Post by **turbulence23** » August 10th, 2007, 4:32 am

haha...

good thing that wasnt your mx tieg... but nice to see that people from all over the world starting to find the dutch community, time for a international section i guess..

small correction to TS, for a full list of our members check incl loads of pics:

http://www.mazdamx-3.nl/members/member_list.php

just stop by on the forum and say hi if you want, always nice to see new people around ( only problem might be that the dutch language might be a little difficult

)

Princess*Precidia · Post by **Princess*Precidia** » August 13th, 2007, 4:06 am

i am VERY HAPPY for you to hear that your car is still in one piece

its way to nice to sit in a ditch!!!

so whoevers pic that may be...i feel sorry for them, but it must have ended up in there due to some kinda reckless driving lol...

turbulence23 · Post by **turbulence23** » August 13th, 2007, 4:09 am

Princess*Precidia wrote:i am VERY HAPPY for you to hear that your car is still in one piece
its way to nice to sit in a ditch!!!

so whoevers pic that may be...i feel sorry for them, but it must have ended up in there due to some kinda reckless driving lol...

wat i can recall is that this guy was driving behind another car on a small countryroad.

the car slowed down, but didnt had it turningsign on, so the mx guy thought that he could overtake him.

when he was next to the car, the other car suddenly turned to the left, and therefore hitting the mx in de side, causing him to fly off the road and into the ditch..

Princess*Precidia · August 13th, 2007, 10:37 am

yikes...poor guy!
its times like this that should remind everyone to use their turnsignals!!!

mx3autozam · Post by **mx3autozam** » August 13th, 2007, 7:51 pm

i should start talking to some of these guys and get them to hook me up with soem eunos side skirts and e-spec head lights!

WhiteFinish · Post by **WhiteFinish** » August 14th, 2007, 6:03 am

Haha...

The headlights are soooooo rare in our country. Used ones you'll still pay 250 euro per headlight !!
If you'r willing to buy them from a dealer you'll pay up to 500 euro per headlight (depending on the dealer).

Wich side skirts do you mean?? Eunos??

Tiga · Post by **Tiga** » August 14th, 2007, 8:15 am

The headlight on my car are modified. Normal lights are all chrome on the inside. I painted the inside black except the reflector part.

pic from another car I did

Post by **Mooneggs** » August 14th, 2007, 9:25 am

hmmm maybe I should paint the inside of my headlights black... I like that look!

to get the glass lense off do you just need to heat it up to separate it?

Tiga · Post by **Tiga** » August 14th, 2007, 10:33 am

Put it in an oven at about 80 degrees Celcius. Then begin at the round side (outside) of the glas and try lifting it very carefully. When you think it cooled down, put it back in the oven for a few minutes and then step by step you can remove the glass.

ninjajim4 · Post by **ninjajim4** » August 14th, 2007, 12:14 pm

some nice custom projectors on that vendor website car...

Post by **Mooneggs** » August 14th, 2007, 2:49 pm

wow I like those alot!

yence · Post by **yence** » August 14th, 2007, 5:02 pm

Sadly, that's just a photoshop.

@Robert: He means the OEM V6 skirts. In the US, the mx-3 was sold without those. It was however on the Japanese/Australian version, named Eunos Presso (correct me if I'm wrong)