wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)

Talon_66 · Post by **Talon_66** » July 24th, 2005, 11:36 pm

babyblueMX3 wrote:I soldered mine..didn't change a thing

Your Tach cuts out at 4500-5000?

babyblueMX3 · Post by **babyblueMX3** » July 25th, 2005, 10:18 am

yup 5k

bmwm3guy · Post by **bmwm3guy** » August 5th, 2005, 11:33 am

any updaes on the Tach problem? I just picked up a 6AL with the Blaster 2 coil and was looking to install it soon. Thanks for the diagram steve... should help a lot. I might give you a call for some backup if you have time

I suck at electronics.

babyblueMX3 · Post by **babyblueMX3** » August 5th, 2005, 1:46 pm

no eric, no updated yet as for me ..maybe talon as his thing working now.
Sure if you ever need help just call, and I'll WALK over your place

wyldside · Post by **wyldside** » June 6th, 2007, 4:32 pm

Did you ever get this tach problem fixed? Was it the incorrect wattage of 1K ohm resistor? You might need a 1 Watt, 1k ohm resistor.

babyblueMX3 · Post by **babyblueMX3** » June 6th, 2007, 5:09 pm

wyldside wrote:Did you ever get this tach problem fixed? Was it the incorrect wattage of 1K ohm resistor? You might need a 1 Watt, 1k ohm resistor.

no I never worked it out, and didn't try it out too. I was using the tach in my MS when I needed it.

Sorry I can't be any help. Probably the msd tach adapter would have work this out

ryan_Fuerte · Post by **ryan_Fuerte** » June 6th, 2007, 6:09 pm

tach adapters dont work, i tried both the msd tach adapters, and my tach was still going crazy..

fowljesse · Post by **fowljesse** » July 14th, 2008, 2:04 am

Old topic revival.
Is anyone running this setup, with no tach problems?
If yes, what is your exact setup (ie, what resistor)?

wytbishop · Post by **wytbishop** » February 21st, 2009, 1:28 pm

I've followed this problem for the past few years and no one that I've read has ever written the solution.

mx3autozam · Post by **mx3autozam** » February 23rd, 2009, 12:02 am

I had a MSD 6A on my car running a klde I ahd in it for a few ays befire I rebuilt it with ZE internals. MY tach wnet funky just past 5000rpm

Fieromx3 also ran a MSD 6AL in his and he tried multiple tach adaptors and resistors and the tach always went fuky at around 5000rpm.

fowljesse · Post by **fowljesse** » March 6th, 2009, 1:47 pm

Boooo.
I'm going to wire this up today, and probably report the same problem. I hope the tach in MegaSquirt works!

fowljesse · Post by **fowljesse** » March 6th, 2009, 9:40 pm

Does anyone know the advantage of using the TIP3055 Transistor instead of the HEI module?

MX-3.com

wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)

Re: wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)

Re: wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)

Re: wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)

Re: wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)

Re: wiring diagram (HEI/msd 6A/klze disty/blaster 2 coil)