i don't understand corksport anymore. not only did they send me Advanz Clear Side Markers whose holes are too tight to fit my bulbs into, their Spoiler/Kits page advertises a J-Spec Front bumper but lists the spoiler\lip for it separately, hardly showing the piece.
This is their J-Spec Presso style front bumper:
and this is their J-Spec Presso front spoiler\lip:
i don't get it. i hardly see any spoiler in the second image: it all looks like one piece ... i don't recall seeing this front bumper on any j-spec mx3's to begin with neway. I thought j-spec front bumpers are the same as e-spec:
Corksport's J-Spec Presso Front Bumper
Corksport's J-Spec Presso Front Bumper
1992 Mazda Precidia
V6 K8 Engine
V6 K8 Engine
- neutral
- Supporting Member
- Posts: 1770
- Joined: December 27th, 2004, 10:19 am
- Location: U.S. Mid Atlantic
That is the J-Spec spoiler. Jschrauwen has it on his too.
Don't see it nearly as often as the straight-line lip. The J-Spec lip is also one continuous piece - see pic below.
There's one on ebay at the moment.
http://cgi.ebay.com/ebaymotors/JDM-OEM- ... enameZWD1V
Don't see it nearly as often as the straight-line lip. The J-Spec lip is also one continuous piece - see pic below.
There's one on ebay at the moment.
http://cgi.ebay.com/ebaymotors/JDM-OEM- ... enameZWD1V
-Jim
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
if your order their j-spec bumper its drilled for the different lip, the holes are higher so you cant use a us-spec lip on it, i know i got the lip from ebay and ordered the bumper from them
and hte lip is not one piece, it is split in the middle into two like the us-spec one
and hte lip is not one piece, it is split in the middle into two like the us-spec one
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
- Aston Wards
- Regular Member
- Posts: 761
- Joined: December 28th, 2001, 2:01 am
- Location: Christchurch, New Zealand
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
this style is on the Eunos Presso, a different trim level than the 30X
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy