slow AND confused...
- DJGypsy
- Regular Member
- Posts: 241
- Joined: June 18th, 2002, 2:01 am
- Location: Lake Mary, Florida, USA
- Contact:
slow AND confused...
i went to the track for the first time the other week. i had a .577 reaction and all my shifts were right on the money, but my ET was 18.7 @ 72.9mph.
i had NOTHING extra in the car. trunk was empty, back seat was empty and i had only like 1/2 tank of gas.
i had the engine (DOHC 1.6) rebuilt @ 115k miles, and it now has 155k miles on it, and it runs as strong as an ox. while it was being re-built i had the head ported and polished. i also have a CAI, 2 1/2" exhaust with 2 resonators and a high flow cat(so basically a straight pipe from the cat to the end), ACT stage 1 clutch, lightweight 14" wheels, h&r springs, tokico HP struts and falken ziex 512 tires.
why am i so slow? i hear about people going faster than this with less modifications than i have.
help.
thanks!
i had NOTHING extra in the car. trunk was empty, back seat was empty and i had only like 1/2 tank of gas.
i had the engine (DOHC 1.6) rebuilt @ 115k miles, and it now has 155k miles on it, and it runs as strong as an ox. while it was being re-built i had the head ported and polished. i also have a CAI, 2 1/2" exhaust with 2 resonators and a high flow cat(so basically a straight pipe from the cat to the end), ACT stage 1 clutch, lightweight 14" wheels, h&r springs, tokico HP struts and falken ziex 512 tires.
why am i so slow? i hear about people going faster than this with less modifications than i have.
help.
thanks!
-Dan
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
- DJGypsy
- Regular Member
- Posts: 241
- Joined: June 18th, 2002, 2:01 am
- Location: Lake Mary, Florida, USA
- Contact:
thanks for the input. i'm graduating this summer with a Bachelors in Engineering Technology this summer. i'm debating between making the MX a project car or a PROJECTILE OFF A CLIFF car...
-Dan
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
The fun of a Project car will alst longer than the excitement of watching it fall a few hundred feet.
Also, the slow thing is nothing more than your lack of time and money in the car. Don't blame it for your lack of attention to it. I know you thought school was more important, but you had your priorities mixed up. Make a fast car first then live in a trailer for the rest of your life.
Also, the slow thing is nothing more than your lack of time and money in the car. Don't blame it for your lack of attention to it. I know you thought school was more important, but you had your priorities mixed up. Make a fast car first then live in a trailer for the rest of your life.

ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
lol well saidAlso, the slow thing is nothing more than your lack of time and money in the car. Don't blame it for your lack of attention to it. I know you thought school was more important, but you had your priorities mixed up. Make a fast car first then live in a trailer for the rest of your life.
“You’ll find, that the only thing you can do easily is be wrong, and that’s hardly worth the effort.”
-
osargeant
- Regular Member
- Posts: 341
- Joined: December 17th, 2001, 2:01 am
- Location: Bridgetown, Barbados
- Contact:
I am also surprised by your times considering the mods, I would be expecting more high 16s or low 17s with that setup since I know of some MX3s 1.6 DOHCs with basic mods like intake and exhaust which are running low 17s. Is your clutch and gearbox in good order?
JSpec Turbo MX3 (1.6 DOHC)
http://www.cardomain.com/memberpage/310985
Port and Polished Head, Ported Intake Manifold, Valve Job, GTX Manifold, Hybrid Turbo, Cone Filter, 2.5" Exhaust, 2.5" Downpipe, ACT Street Clutch, Lightened Flywheel, MSD 6A Ignition, Boost Retard and SS Coil, Magnecor Plug Wires, Denso Iridium Plugs, UR Lightened Pulley, Spearco FMIC, Turbo XS BOV & MBC, BEGI RRFPR, Supra Injectors, Walbro 255 Fuel Pump, Autometer Gauges, Pivot Shift Light
http://www.cardomain.com/memberpage/310985
Port and Polished Head, Ported Intake Manifold, Valve Job, GTX Manifold, Hybrid Turbo, Cone Filter, 2.5" Exhaust, 2.5" Downpipe, ACT Street Clutch, Lightened Flywheel, MSD 6A Ignition, Boost Retard and SS Coil, Magnecor Plug Wires, Denso Iridium Plugs, UR Lightened Pulley, Spearco FMIC, Turbo XS BOV & MBC, BEGI RRFPR, Supra Injectors, Walbro 255 Fuel Pump, Autometer Gauges, Pivot Shift Light
- DJGypsy
- Regular Member
- Posts: 241
- Joined: June 18th, 2002, 2:01 am
- Location: Lake Mary, Florida, USA
- Contact:
osargeant wrote:I am also surprised by your times considering the mods, I would be expecting more high 16s or low 17s with that setup since I know of some MX3s 1.6 DOHCs with basic mods like intake and exhaust which are running low 17s. Is your clutch and gearbox in good order?
gearbox and clutch are fine. i have an ACT stage 1 in there from corksport. chirps 2nd gear HARD, even with the 205/60R14 falken 512's i have on the car.
-Dan
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
- jaydog5678
- Regular Member
- Posts: 1043
- Joined: March 27th, 2002, 2:01 am
- Location: Marietta, GA,
- Contact:
LOL. I'm gonna make this a signature quote.PATDIESEL wrote:
The fun of a Project car will alst longer than the excitement of watching it fall a few hundred feet.Make a fast car first then live in a trailer for the rest of your life.
The DOHC 1.6 has 105hp, but may as well be around 88hp to the whls. Mine dynoed at 92hp before the swap.PATDIESEL wrote:88 HP, 1.6L is the problem
-
hgallegos915
- Senior Member
- Posts: 6451
- Joined: June 19th, 2004, 2:01 am
- Location: El Paso Tx U.S
- Contact:
if u dont want the car ill gladly take it for free.
-hec
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
- DJGypsy
- Regular Member
- Posts: 241
- Joined: June 18th, 2002, 2:01 am
- Location: Lake Mary, Florida, USA
- Contact:
heh, if i could get all the money back out that i have put in, i might think about it. problem is, i cannot be without a car. i gotta be able to get around 
-Dan
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
(SOLD) '94 RS, rebuilt B6 DOHC engine & cyl head, ACT clutch, e-bay CAI, 2 1/4" exhaust, wide open resonator w/ stock muffler, H&R springs, Tokico HPs, front strut tower brace, KVR drilled rotors w/ carbon fiber pads, Falken tires, Impostor lightweight wheels, Kenwood & MTX sound.
straights are for fast cars, turns are for fast drivers.
- Limegreen mx-3
- Regular Member
- Posts: 1778
- Joined: October 29th, 2002, 2:01 am
- Location: San Antonio TX
- Contact:
i ran a 17.3 with my sohc 1.6 but thats with cai 2 1/4 in exhaust piping dualfriction centerforce clutch on VP fuel. i added more mods and i best i got was 16.9something. thats the best i could get it on the sohc bought another 92 mx-3 slap a BP now i wonder what i run.
(12.4@118@18psi) 92 MX-3, KIA (BP-DE)Swap, Electromotive TEC II Standalone, 8,200 Rev Limit, Custom Intake/Exhaust Manifold, 1,000cc PTE Injectors, Custom Fuel Rail, Aeromotive FPR, 80MM Holley TB, MSD 8.5MM Wires, NGK V-Power #8, SC6262 Turbo, 3 in. DownPipe, Tial WG/BOV, 600HP PTE FMIC, 2.5IN Intercooler Piping, EQUUS/Autometer KIA G-Series Tran, Extreme ACT Clutch, Built BP in starting process.