Hi I am driving to my car 2 hrs away tomorrow to change the starter and try to get it running. I have never changed the starter before and I don't want to bring more tools than I need. So if anyone can tell me what tools I am going to need, it would be very helpful. Also include any wiring tools like wire cutters or crimpers, etc. Thank you!
Steve
What tools are needed to install new starter?
-
- Regular Member
- Posts: 339
- Joined: January 9th, 2004, 2:01 am
- Location: Philly
- Contact:
What tools are needed to install new starter?
www.illegalCustoms.com
Tri-State Area Car Club
Tri-State Area Car Club
- ovendenk
- Supporting Member
- Posts: 911
- Joined: January 12th, 2004, 2:01 am
- Location: Kamloops, BC
- Contact:
decided that was the cause? i just did mine on friday. keep in mind mine is the v6, but all you should need is a basic socket set. not 100% sure what's in the way to get access to the starter in the 4-cyl but it should be just 3 bolts holding the starter to the engine and a couple of wires. shouldn't be too hard, i got mine done in a 1/2 hr and it was my first ever. only one thing:
MAKE SURE TO DISCONNECT BATTERY FIRST.
good luck.![Smile :)](./images/smilies/icon_smile.gif)
MAKE SURE TO DISCONNECT BATTERY FIRST.
good luck.
![Smile :)](./images/smilies/icon_smile.gif)
kevin (aka The Oven)
93 mx-3 GS KL-ZE with KL31 cams and properly chipped ecu
All mods are on my website: http://ca.geocities.com/ovendenk
MX-3.com Worklog: http://www.mx-3.com/phpbb2/viewtopic.php?t=48462
![Image](http://ca.geocities.com/ovendenk/pics/Other/sig.jpg)
93 mx-3 GS KL-ZE with KL31 cams and properly chipped ecu
All mods are on my website: http://ca.geocities.com/ovendenk
MX-3.com Worklog: http://www.mx-3.com/phpbb2/viewtopic.php?t=48462
![Image](http://ca.geocities.com/ovendenk/pics/Other/sig.jpg)
- ovendenk
- Supporting Member
- Posts: 911
- Joined: January 12th, 2004, 2:01 am
- Location: Kamloops, BC
- Contact:
Grants wrote:I think someone forgot on FridayMAKE SURE TO DISCONNECT BATTERY FIRST.
![Laughing :lol:](./images/smilies/icon_lol.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
![Wink :wink:](./images/smilies/icon_wink.gif)
kevin (aka The Oven)
93 mx-3 GS KL-ZE with KL31 cams and properly chipped ecu
All mods are on my website: http://ca.geocities.com/ovendenk
MX-3.com Worklog: http://www.mx-3.com/phpbb2/viewtopic.php?t=48462
![Image](http://ca.geocities.com/ovendenk/pics/Other/sig.jpg)
93 mx-3 GS KL-ZE with KL31 cams and properly chipped ecu
All mods are on my website: http://ca.geocities.com/ovendenk
MX-3.com Worklog: http://www.mx-3.com/phpbb2/viewtopic.php?t=48462
![Image](http://ca.geocities.com/ovendenk/pics/Other/sig.jpg)
-
- Regular Member
- Posts: 339
- Joined: January 9th, 2004, 2:01 am
- Location: Philly
- Contact: