![Froggie Red :froggie_red:](./images/smilies/froggie_red.gif)
what turbo parts are used for th t3/t4 hybrid???
-
- Regular Member
- Posts: 68
- Joined: February 6th, 2004, 2:01 am
- Location: morristown,tn.
what turbo parts are used for th t3/t4 hybrid???
and also were the hell can i find a rebuild kit for a garrett t3 turbo... and would 2 inch piping be good enough for my turbo are should i go bigger ???? ![Froggie Red :froggie_red:](./images/smilies/froggie_red.gif)
![Froggie Red :froggie_red:](./images/smilies/froggie_red.gif)
"get some!"
- babyblueMX3
- Supporting Member
- Posts: 3755
- Joined: February 23rd, 2003, 2:01 am
- Location: Gatineau,Quebec,Canada
- Contact:
Re: what turbo parts are used for th t3/t4 hybrid???
you need to be more specific..what pipes are you talking about..well first of all..you got the 4 banger or v6 ??? this changes the whole piping situation and size...
RIP 400whp ZE-T MX-3
Current car : Golf 01 GTI 1.8T (15 psi)
Current car : Golf 01 GTI 1.8T (15 psi)
-
- Regular Member
- Posts: 68
- Joined: February 6th, 2004, 2:01 am
- Location: morristown,tn.
Re: what turbo parts are used for th t3/t4 hybrid???
its a manual sohc 1 .6 and i was referimg to intercooler piping. ![Driver :driver:](./images/smilies/driver.gif)
![Driver :driver:](./images/smilies/driver.gif)
"get some!"
-
- Regular Member
- Posts: 629
- Joined: November 21st, 2002, 2:01 am
- Location: Weyers Cave, VA
- Contact:
Re: what turbo parts are used for th t3/t4 hybrid???
Anything under 300HP I'd use 2.25" IC pipes. 300-400HP use 2.25" from turbo to IC, then 2.5" from IC to throttle body. 400-500HP use 2.5" IC pipes. 500HP+ 3" IC pipes. These are general guide lines, to get the best results you need to try different combinations. If you need to rebuild your turbo I'd suggest looking into a ball bearing CHRA that will fit your exhaust housing. Yes it costs more, but it will last a LOT longer and handle a LOT more boot. E-mail me if you'ld like me to see what I can find for ya. ![Welder :welder:](./images/smilies/welder.gif)
![Welder :welder:](./images/smilies/welder.gif)
http://www.cardomain.com/ride/354836
B6T, APEXi Silvia IC, HKS SSQV, Magnacore KV85 Wires, NGK V-Power, Haltech E6K, Accel 300+ Digital Ign w/ coil, Accel 375+ controller, JWMmotorsports turbo manifold & exhaust, custom Garret GT-R series turbo, MAZDASPEED mounts, SRD Bushings, Pacesetter Short Shift, entire Pro LX drive train w/ custom ACT clutch (I'm the first to succeed this on B6T), Weapon-R, and lots more stuff!
B6T, APEXi Silvia IC, HKS SSQV, Magnacore KV85 Wires, NGK V-Power, Haltech E6K, Accel 300+ Digital Ign w/ coil, Accel 375+ controller, JWMmotorsports turbo manifold & exhaust, custom Garret GT-R series turbo, MAZDASPEED mounts, SRD Bushings, Pacesetter Short Shift, entire Pro LX drive train w/ custom ACT clutch (I'm the first to succeed this on B6T), Weapon-R, and lots more stuff!
- monty73741
- Forum Moderator
- Posts: 2651
- Joined: February 11th, 2001, 2:01 am
- Location: baltimore,md usa
- Contact:
Re: what turbo parts are used for th t3/t4 hybrid???
instead of turbo why not the bpt\bp
Jason Danaher
Please Help Support MX-3.com
MX-3.com Online Store - http://www.mx-3.com/osv3
CafePress - http://www.cafepress.com/mx3com
Please Help Support MX-3.com
MX-3.com Online Store - http://www.mx-3.com/osv3
CafePress - http://www.cafepress.com/mx3com