so anyone running a bpt with there stock rad
dose it ever overheat
when
any other info
if your running an aftermarket rad which one
thanks
Stock rad with bpt
Stock rad with bpt
1993 MX-3 GS V6 - Stock
2004 MazdaSpeed MX-5
2004 RX-8 - Project
2004 MazdaSpeed MX-5
2004 RX-8 - Project
-
- Regular Member
- Posts: 89
- Joined: December 29th, 2002, 2:01 am
- Location: hull ottawa
- Contact:
Re: Stock rad with bpt
i am running my bpt on my stock rad
but i also have a IC
my needle is at the same place a bit over the middle never over heats even at top speeds
<small>[ February 12, 2004, 05:47 PM: Message edited by: philcosta ]</small>
but i also have a IC
my needle is at the same place a bit over the middle never over heats even at top speeds
<small>[ February 12, 2004, 05:47 PM: Message edited by: philcosta ]</small>
http://www.cardomain.com/id/phil_costa
<img src="http://smkclan.com/images/snake/articbeast.jpg" alt=" - " />
<img src="http://smkclan.com/images/snake/articbeast.jpg" alt=" - " />
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: Stock rad with bpt
phil, i gotta say i love your car man
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
-
- Senior Member
- Posts: 2334
- Joined: September 17th, 2001, 2:01 am
- Location: Jacksonville, FL, U.S.
Re: Stock rad with bpt
i never had a problem. if it starts to get warm, drop down to the next thermostat.
Fast imports only come on two wheels.
"MR." Ashley Fowler
'02 Yamaha Warrior (1700cc)
'94 MX-3 RS-t (BPT)~ sold
cardomain pics
"MR." Ashley Fowler
'02 Yamaha Warrior (1700cc)
'94 MX-3 RS-t (BPT)~ sold
cardomain pics
-
- Regular Member
- Posts: 89
- Joined: December 29th, 2002, 2:01 am
- Location: hull ottawa
- Contact:
Re: Stock rad with bpt
thanks papa roachOriginally posted by papa roached:
phil, i gotta say i love your car man
http://www.cardomain.com/id/phil_costa
<img src="http://smkclan.com/images/snake/articbeast.jpg" alt=" - " />
<img src="http://smkclan.com/images/snake/articbeast.jpg" alt=" - " />