how to shave emblems
how to shave emblems
does anyone have any advice on how to shave the emblems on the mx3?? how tro fill in those little wholes fomr the decal?
Turbo 2.5l mx3
-
- Regular Member
- Posts: 389
- Joined: March 16th, 2003, 2:01 am
- Location: Newark, DE, USA
- Contact:
Re: how to shave emblems
Are you talking about the holes on the hood? There are no holes on the trunk. The emblems are just stuck on.
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
Re: how to shave emblems
weld very carefully not to warp metal or just fiberglass it in...I wouldnt use bondo, cracks easier.
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
Re: how to shave emblems
Bondo would do just fine for those tiny holes.
Combat kit, Spectra blue paint, shaved, Black ADR flite 4 17's/ Yokahama ES 100's, straight through 2.5 inch cat back exhaust, CAI, Straight neck IM KLZE, poly filled motor mounts, Kl48/ Eprom chip, black altezzas, Wet Zex 75 shot, Walbro 255 fuel pump, Cosmo AFPR, GS SE all black interior, RF 1kbd amp, RF 12 HE2's (2), US acoustics 4 channel amp
My Cardomain site
My Cardomain site
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: how to shave emblems
You can take the emblems off with dental flosss.
-
- Regular Member
- Posts: 584
- Joined: February 7th, 2003, 2:01 am
- Location: Carlisle, MA. USA
- Contact:
Re: how to shave emblems
Funny, cuz I have tried the back ones with dental floss, and they have never come off.... Am I stupid?
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: how to shave emblems
I hope not Thats how I got mine off. Saw it off with good dental floss.
-
- Regular Member
- Posts: 369
- Joined: September 16th, 2002, 2:01 am
- Location: minnesota
Re: how to shave emblems
the way i shaved off my emblems was just take a hair blow dryer heat if up and then do as barry said and use dental floss tho fishing line worked for me
sold the mx-3 , bought 04 gtp comp g , from the smallest v6 to one of the biggest 3800 s/c FTW
- johnnyb
- Supporting Member
- Posts: 1079
- Joined: January 26th, 2003, 2:01 am
- Location: Brampton, On, Canada
Re: how to shave emblems
the rear ones are just double-sided tape. The front one is 2 pins in the hood and double sided tape. if you want to help fill in the holes use the little plastic clips that the pins on the emblem go into to fill in the holes a bit and then just sand the caps off of them.
-
- Regular Member
- Posts: 584
- Joined: February 7th, 2003, 2:01 am
- Location: Carlisle, MA. USA
- Contact:
Re: how to shave emblems
<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by Custommx3:
I hope not Thats how I got mine off. Saw it off with good dental floss.<hr></blockquote><p>HAHA classic Barry. Good one!
I hope not Thats how I got mine off. Saw it off with good dental floss.<hr></blockquote><p>HAHA classic Barry. Good one!