I am ready to cut it off!!
I am ready to cut it off!!
Swapers ... I am to the point where I am removing the shift control rod from the linkage... I have pounded and pounded on the bolt tring to get it to come out....I unbolted the shifter and let it fall on the pipe to relese any pressure that may have been on the bolt....I have even used a jack to push the bolt thru ...to no avail ..I am ready to cut it off with a dremal. I called mazda parts and a new one is only 25 bucks ....that sound right??? He gave me the part number of F52917491 and advice on removing this pig. As you can see I have rounded the end of the bolt hammering.... god my neck hurts
<p>[ April 15, 2003: Message edited by: Cage ]</p>
<p>[ April 15, 2003: Message edited by: Cage ]</p>
-
- Regular Member
- Posts: 1333
- Joined: December 11th, 2000, 2:01 am
- Location: Saskatoon, SK, Canada
Re: I am ready to cut it off!!
Spray it with liquid wrench and let it sit. Come back to it in a few a bit and tap it with a hammer, should go straight up. Just wiggle it if you have to, use the hammer to bang any rust off.
Chris Malden
MX-3 RSR
chris.malden@sasktel.net
chris.malden@sasktel.sk.ca
B6T Swap Info |IHI Turbo Sources
MX-3 RSR
chris.malden@sasktel.net
chris.malden@sasktel.sk.ca
B6T Swap Info |IHI Turbo Sources
Re: I am ready to cut it off!!
got it ...bigger hammer thanks<p>cage
-
- Regular Member
- Posts: 1333
- Joined: December 11th, 2000, 2:01 am
- Location: Saskatoon, SK, Canada
Re: I am ready to cut it off!!
Looking from below the car upwards, is that threaded section pointing down? If so, you are working on the correct bolt, if the other bolt is the one that points down then you need to start working on it instead. A BFH really does work well though.
Chris Malden
MX-3 RSR
chris.malden@sasktel.net
chris.malden@sasktel.sk.ca
B6T Swap Info |IHI Turbo Sources
MX-3 RSR
chris.malden@sasktel.net
chris.malden@sasktel.sk.ca
B6T Swap Info |IHI Turbo Sources
Re: I am ready to cut it off!!
hehe, i had that same problem. it was a real P.I.T.A. i ended up spraying it with WD40 and putting a jack under it, then hammering it, and pulling (jiggled it a bit too) the top of the bolt with pliers.<p>*** make sure you wear goggles when you do that. i almost got rust-dust in my eyes.
-
- Regular Member
- Posts: 311
- Joined: August 23rd, 2002, 2:01 am
- Location: Kitchener, Ontario Canada
- Contact:
Re: I am ready to cut it off!!
i did this at the start of the new year
mine came out with a soft tap from my wrench
but then a huge piece of undercoat fell and went in my eye
mine came out with a soft tap from my wrench
but then a huge piece of undercoat fell and went in my eye
NoVa<p>
- Zoso124
- Forum Moderator
- Posts: 1100
- Joined: November 7th, 2000, 2:01 am
- antispam: No
- Location: Sterling, VA
Re: I am ready to cut it off!!
Grind the b*stard off at the top. I wasted 4 hours yesterday on that same DAMN BOLT!!!! AHHHHHH<p>When your gonna have to drill it out. All you need is a regular bolt, don't buy one from Mazda. If I knew the size I would tell you but I won't be down at my parents on friday to finish building the other motor.<p>IF YOU GRIND IT OFF, BE CAREFUL THAT RIGHT WHERE THE FUEL FILTER IS!!!<p>[ April 16, 2003: Message edited by: Zoso124 ]</p>
Mike Evans
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
-
- Senior Member
- Posts: 3391
- Joined: November 30th, 2001, 2:01 am
- Location: Stuttgart, Deutschland
- Contact:
Re: I am ready to cut it off!!
I had this problem when I installed bronzeoil bushings on my car. The bushings froze to the bolt....and i had a hell of a time getting that bolt off.<p>I got a dead blow hammer and beat the **** out of it while turning it with a wrench...it eventaully came out, but it took FOREVER.<p>A bolt costing 25 bux? screw that, get one from a junkyard or something.
Noble Green Metallic 93' GS Hybrid, 91' 1.8 323
DONATE TO MX-3.COM
DONATE TO MX-3.COM
- Zoso124
- Forum Moderator
- Posts: 1100
- Joined: November 7th, 2000, 2:01 am
- antispam: No
- Location: Sterling, VA
Re: I am ready to cut it off!!
Wait hold on, move that rubber boot back, my dad just called me and told me there is a bolt in there and all you have to do it take it out. I still can't believe, all the freaking work and it said it was so simple to take this other bolt out. We'll I guess I'll see it Friday morning. I'll take a few pics.
Mike Evans
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
-
- Regular Member
- Posts: 758
- Joined: January 10th, 2001, 2:01 am
- Location: auburn, ny
- Contact:
Re: I am ready to cut it off!!
yes, if you pull that boot back there is a 10mm bolt under there that comes out easily, :p :p
DRAG SPEC MX3 BEING PARTED OUT.
BUY ALL MY STUFF OR DIE.lol, SERIOUSLY BUY MY STUFF. PLEEEASE
BUY ALL MY STUFF OR DIE.lol, SERIOUSLY BUY MY STUFF. PLEEEASE
- Zoso124
- Forum Moderator
- Posts: 1100
- Joined: November 7th, 2000, 2:01 am
- antispam: No
- Location: Sterling, VA
Re: I am ready to cut it off!!
It would have been nice if one of my three manuals showed that.
Mike Evans
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
-
- Regular Member
- Posts: 603
- Joined: August 2nd, 2001, 2:01 am
- Location: Brantford, Ontario, Canada
- Contact:
Re: I am ready to cut it off!!
well I had the same prob when I did my swap, and my manual never showed a bolt under the rubber either. So I just left it on the tranny. I had the car jacked up high and just lifted the engine out with the tranny and the shifter linkage all at once! This worked out fine for me, no probs.
92 MX-3 GS 2.5 KLZE
14.385 @ 98.21
14.385 @ 98.21