cam regrind for kl03 and klze
-
- Regular Member
- Posts: 295
- Joined: November 19th, 2001, 2:01 am
- Location: Edmonton,AB,CA
- Contact:
cam regrind for kl03 and klze
<A HREF="http://www.probetalk.com/forums/showthr ... genumber=1" TARGET=_blank>http://www.probetalk.com/forums/showthr ... perpage=40& pagenumber=1</A><p>[ October 14, 2002: Message edited by: mrprecidia ]
You can just call me the originator
-
- Regular Member
- Posts: 295
- Joined: November 19th, 2001, 2:01 am
- Location: Edmonton,AB,CA
- Contact:
Re: cam regrind for kl03 and klze
i hope that you guys are atleast looking at this if you are not responding.
You can just call me the originator
Re: cam regrind for kl03 and klze
Sounds like a good idea, but for some reason people are doubting this guy and his cams delivering the claimed power. But what do I know. I don't even have a ze yet. [img]shrug.gif"%20border="0[/img]
Re: cam regrind for kl03 and klze
someone bought a grind from him and lost their car for a while because the grind was bad
93 Mx-3 GS klze swapped(sold)
96 Integra LS DD
91 Crx Si drag car
2.0L sleeved gsr block, forged internals, skunk2 valvetrain, HP racing intake manifold, Holset H1 turbo, 1000cc injectors, short geared lsd transmission, 3" turboback exhaust. 20 psi![Smile :)](./images/smilies/icon_smile.gif)
96 Integra LS DD
91 Crx Si drag car
2.0L sleeved gsr block, forged internals, skunk2 valvetrain, HP racing intake manifold, Holset H1 turbo, 1000cc injectors, short geared lsd transmission, 3" turboback exhaust. 20 psi
![Smile :)](./images/smilies/icon_smile.gif)
-
- Regular Member
- Posts: 295
- Joined: November 19th, 2001, 2:01 am
- Location: Edmonton,AB,CA
- Contact:
Re: cam regrind for kl03 and klze
is it posible to take his cam specs and take them to a local machine shop and have them grind them?
You can just call me the originator
-
- Regular Member
- Posts: 30
- Joined: October 13th, 2002, 2:01 am
- Location: Austin, TX
- Contact:
Re: cam regrind for kl03 and klze
Hmm...sounds like something that is going to end up in my ZE...
You did what to what?!?!
Re: cam regrind for kl03 and klze
Sure, if someone can grind cams you can give them the specs, though it may cost more. This guy is going to produce cams of certian dimensions depending upon orders.
-
- Regular Member
- Posts: 1179
- Joined: August 27th, 2001, 2:01 am
- Location: Russellville, AR, USA
Re: cam regrind for kl03 and klze
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by mrprecidia:<BR><STRONG>is it posible to take his cam specs and take them to a local machine shop and have them grind them?</STRONG><HR></BLOCKQUOTE><P>Sure, if you knew what ALL of the specs were. You can't reproduce a grind with just the lift and duration. <P>He's pretty secretive of his specs and for good reason, it's his effort that went into the specs and he makes money from it.
KLZE, ZE PCM, UR pulley, PS catback, PS STS, PRM, IAC bypass, 64mm TB, FOP hair gel
-
- Senior Member
- Posts: 2516
- Joined: November 7th, 2000, 2:01 am
- Location: Gainesville, FL USA
- Contact:
Re: cam regrind for kl03 and klze
The person who lost power had really sketchy figures, which point to improper timing on installation. Mike Seli knows his stuff very well; we've talked cam profiles on multiple occasions. If I had the dough, I would get 3 things to make a mean streetable ZE: FPR, Headers, and Mike's cams. Should be good for near 200whp.
David Coleman
I used to know alot about MX-3's, but not so much anymore. Oh well.
I used to know alot about MX-3's, but not so much anymore. Oh well.
Re: cam regrind for kl03 and klze
has anyone gotten a set of these cams on a dyno yet?