MX-3.com

I finally got my engine done, an fired up to boot!
check out the look of the block at the first an threw to the end where it is finished.
Just a little improvement.

http://www.cardomain.com/memberpage/552384

Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384

Well I have them or I should say it, in, The top two centre studs have to be removed an two 14m hex bolts has to be used because there isnt enough clearance for the nuts on the studs against the pipe. Also I used lots of that High temp silicon around the flange gasket. I took a file an trued the fac...

How much for the front lip?

Some things you can do to get more power out of your 1.6dohc engine are: Disconect the hot water going threw your throttle body,dont forget to reconnect it for the winter. Get a (i forget the materal used )aftermarket heat insulating spacer for the intake.these are made for the miata 1.6, they use a...

Sounds interesting MX3ze, do you have any pic of it on your car?

Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384

Here is a unhealthy looking ground point I found on my 1.6dohc. it hides real good under the wire harness. Here is a pic of it check it out http://www.cardomain.com/memberpage/552384/8 I will be fixing this soon as posible. Eugene L 1.6DOHC N.S.canada http://www.cardomain.com/memberpage/552384

Kewl.
I'd be such a dead man with one of those. I drove my KX-250 an RZ-350 like a tard for years not a scratch, got on my brothers honda 70 and almost became a organ donator,LOL

Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384

Glad to hear your all right guy ....... now for something totaly stupid!

...Whats a Ped? .. I work with a few Speds! but I dont think its the samething , LOL


Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384

I have the block back in my car now. The head is ported an just has to have the valves seated, I should have it back in this week,I will have the rest of the installation piks for the probe header by the weekend.

Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384

I was bored an decided to play with photoshop, I should of been using the time to work on my car though, SLACKER! lol. but anyway I photoshoped the exedy poster to be somewhat a MX-3 :confused2: http://www.cardomain.com/memberpage/552384/7 Eugene L 1.6DOHC N.S.canada http://www.cardomain.com/memberp...

"Sorry I forgot to mention I had a spare key. I was just wanting to know how to stop the thieving git from simply driving my car away." Remember the anti-thieft system Mad Max had under his car! HuhuheheHaawh! LOL Eugene L 1.6DOHC N.S.canada http://www.cardomain.com/memberpage/552384

The escort gt 1.8 T body only cost me $20 no big deal, I might pick up this engine for $100 anyway ,now I can ask for a deal becauser it doesent have a T body ,LOL! anyway has anyone had the stock T body machined/bored to 60mm or if there is enough metal to do this. I am going to check with my machi...

As far as I know the miata head is the same as the mx head, the only differance is where the distributor is located,the stock miata cams are hotter than the mx cams though.these cams can be used in the mx head with mods.one bonus of using a miata head is the availibility of different drop in cams an...

As for the 1.8 ford escort GT the throttle body doesent fit,bolt patern is different and is 55mm any way, same as my 1.6dohc. I picked it up at a local yard today an campared the two when I got home.

Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384

That sucks bigtime guy!
Glad to hear your allright though, and your mx didnt meld with the concreat.
If you have the quid, the rebuilt or the LSD one because you should at least get some type of warranty with them.

Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384