MX-3.com

<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by Pedro: bump<p>c'mon somebody? <hr></blockquote><p>return the cv kit and buy a new axle ...$49.50 Lifetime warranty here in the US. I didn't think replacing the cv boot was a big deal until I to...

<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by lazzyie: You can use the klze distributor, the wiring harness should be a tad different, you gotta wire up an outside coil, the problem being with using the klze disty is that you have to use k...

Well ..the Kl-ZE is almost ready to be placed into the car ...everything is done ...The bad news is the tierods and the balljoints are all on backorder....so I am not going to driving until friday...this gives me another paycheck to get the Motor mounts and the MSD ignition and coil..The 1.8 may be ...

Nope didnt have a pin...just had to whale on it with the crow bar..splined shaft pulled right out neat and clean....easy when its on the floor
Thank you guys ..was really worried ...<p>Cage

...does this mean teardown ...Fuc*. <p>Cage

<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by Aiden: Aren't MX-3 flywheels only 9 lbs???<p>If so, why bother with a PGT flywheel at all, or an aluminum one???<p>~A <hr></blockquote><p> The Mx-3 Flywheel is 18LBS The 2.5 probe flywheel is 2...

Sorry,I ment the timing belt tensioner ..guess i been breathing to many fumes from the brake parts cleaner :D ..he said no problem he is going to shave 3 LBS (he thinks) $120 .00 (2 hours labor)..better than spending $320.00 on a aluminum flywheel. (I hope)! I really didnt want to get an 11 LB alumi...

no ...not to lazy to put it on I was just kidding ... it was hard (very)hard getting it off and even harder puting it back on! :) Mostly this post was questing why hondas don't have theirs on but we do. Is it their more flash and show and we are all about reliablity ?? Are hondas less at risk in tha...

It's not that I want to remove it ...it's that I don't want to put it back on hehe.. I about to change the Water pump and the Timing belt. I was just curious as to why modded honda's don't have the cover on. didn't know if it was a Vtech thing ..OMG I sad a bad word :p <p>Cage

I always see honda engines running with out their timing belt cover... what are the dangers and why would it be a horable idea to leave the cover off? <p>Cage

Called every Machine Shop within 100 miles and nobody would shave my flywheel... they tell me to buy a new one...I would if I had 320 Bucks! anyway one guy wants me to bring it in so he can tell me if he can do it. This hads been a major hold up today...thinking about scraping the flywheel shaving i...

Today was a good day no surprises! The engine is out and on the floor. The bell housing is removed and the flywheel is ready to be taken tomorrow to be lightend. I noticed the clutch from Act is a bit wider...don't think it will be a problem. Picking up parts on order tomorrow. I don't know if anybo...

Well, Day three... all the axles are pulled, all the heater hoses are pulled as well as all connectors relating to sensors and vacuum are pulled and labeled...even took pictures with the digital of most connectors just to be sure, I would connect them correctly. I am taking Valds advise and going to...

got it ...bigger hammer thanks<p>cage

Swapers ... I am to the point where I am removing the shift control rod from the linkage... I have pounded and pounded on the bolt tring to get it to come out....I unbolted the shifter and let it fall on the pipe to relese any pressure that may have been on the bolt....I have even used a jack to pus...