MX-3.com

Hello, I am selling my black 1993 Mazda MX-3 GS. The car was running well up until about a week ago when the car spun a bearing. The car has KLDE swapped in. The body is in good condition the front bumper is broken due to being towed and it has a 2inch dent near the gas cap and the normal dings of a...

Originally posted by Gro Harlem: omg...this thread is so full of misinformation i'm not even going to begin to comment. There might be A lot of misinformation in this thread, but the information provided by Yoda (Vaughn) is probably as good as can get. No one and I mean no, on here has done as much...

The suspension, under that kind of a setup will be benefical in two ways. The first way is that it will, depending on the type of materials you use and the welding technique, make the part much stronger than stock. Thus improving handling, while also if you use materials such as chrome-moly, aluminu...

Originally posted by hgallegos915: I just realized that my front engine mount is cracked...where do i get these :/ are they that pricey? How bad is the crack in your motor mount? The reason that I ask is if the crack is a small to medium size crack. Then I would recommend you to take the bracket, s...

I know there was some interest on the board about some solid swaybar links. Which arent really solid, as they are made using heim joints. I can obtain and put together a set for the front or rear for $45usd+shipping . Ill try to get some pics up of the ones that I have made for my own car. post here...

-A set (ds and Ps) of Lower Balljoints. These are for post 3/93 build mx-3's. $40usd+shipping -Set of inner tie rod ends, post 3/93 build mx-3's $40usd+shipping (The pre 3/93 Lowerball joints and inner tie rods are different so please make sure these will work for your application.) -MSD 6a bought u...

I am actually in the process of building my Megasquirt ECU. But just so you know that you will be able to buy a fully built MegasquirtnSpark programmed for a KL-engine, keeping all of your stock accessories for around 350 dollars, just watch probetalk for it. Megasquirt is juat as good as any other ...

Jarid, Do you want to make the whole door panel into fiberglass or just the carpeted part? If its the whole door panel you can lay a sheet of fiberglass right over the whole panel, and add resin then mold it on there. Then keep adding layers, until it strong enough. Imho, i think that if you were go...

Well I would never intend on one person to do it all themself, as i agree with you it is a daunting task to do. I guess what i meant was more like a thread in which if you've done a retrofit, post in it and put as much as you can, interms of information.If said thread ever did occur, it would be nic...

Even though this wouldnt be as easy as having a company make a set of headlights for our cars. It sure would be great if some people who have done a retrofit could post step-by-step pics of the whole process start to finish. With some quality instructions. I know that searching this very forum, bits...

Originally posted by mazdubber: Unfortunately I could not race the corrado because he said that his 3rd gear syncro is fu(ked . Ah the VR's weak link, the tranny. A VW always has a weak point. Tell that guy with the corrado to buy one of the few custom trannys out there for the VR's. They are defin...

When you go pick it up make sure you tell them that you want it left on a pallet, that way it makes it easier to grab on too. After that three people shjould be able to lift it with ease, im sure the engine is probably only a round a few hundred pounds.

Originally posted by mazdubber: Well, since the Corrados VR6 is a 2.8L stock...then I'd say a 2.9 would have some work done. VR's are very good motors. Bullet proof and tourquey. Sound's very similar to a GS's V6. Actually the 2.9l VR6 is a stock motor for the Corrado in Europe for the 1995 model y...

Sam the stock KLDE manifold (US Spec MX6) will fit, with no problems at all. I just installed mine over the weekend, the only thing that you are going to need to find is a rubber 90 degree elbow from somewhere like Home Depot to go from the TB to the VAF. Email or IM me if you have any questions, Mi...

Wil,

According to a member of probetalk that I talked too, he said that the stock PGT fuel pump flows 90 lph. You might want to try and search PT.