MX-3.com

is this for the 1.6(b6de)? im very very interested

how much for the manifold and the egr tube? im more concerned abouth the tube that runs from the drivers side of the manifold to to the drivers side under the intake manifold. how much shipped to oshawa ontario L1H1T5

well id check compression then it must just have low compression then causing it not to start. have you pulled your timing cover on the passenger side off? maybe it had skipped and now broke? have you replaced it recently within 80000kms? id say its either timing or compression if you have spark and...

1. check and see if your timing belt skipped a tooth or two/ check your timing using a pin between ur ten and ground i think dont just move your distributor. if your just twisting your distributor that could be messing it up too. 2. you said its turbo? what fuel management are you using? if a fmu ma...

theres a better explanation i found on a web site that sells kits if you looked on the site theyd probably show different compounds, wheels and their different uses. the finish depends a lot on the SANDING being even though Eastwood offers Buff Kits which supply everything you need for polishing alu...

yeah theres a lot of steps to do it properly the black compound is what takes any sanding lines out. its about 5-6 inches long and an inch in diameter. green is the same it just wont take out you sanding lines its the final high polish just shines it up. if you sanded with 4000 grit maybe you dont n...

http://www.hollywoodinc.ca/Gallery%20photos/011.jpg" onclick="window.open(this.href);return false;
some c5 wheels i high polished

all you need to do is get it smooth and remove any corrosion final sand it with 600 grit. use a die grinder with a skinnier cloth cutting wheel and black compound this will make it nice and smooth( make sure you dont push too hard it will smudge the compound which is a b---- to get off) then with a ...

i just had a similar issue. check your voltages on your distributor clips, if your getting the proper volts then its your distributor. with mine i thought it was the distributor but when i checked the voltages on the 3 pin disty clip neither ground was grounding but i was getting power where i shoul...

finally after a week of tinkering and replacing my burnt up main engine harness it fired and is alive:) 3 days i swapped distributors like 6 times and it was the 3 pin clip to the distributor that was fu--ed, put a new one on and vroom vroom. i won't say zoom zoom cuz i think its in limp mode from t...

okay so my voltages across the top pin are from left to right ( .02, 13.3, .56, .56, .01, .03). on the 3 pin the it reads ( 0, 12.5, 0) is this correct? i think this 3 pin connector is wrong.
i am now getting a code 3 and 35 how do i remedy these issues? code 3 crankshaft sensor?

thank you so much for the help im going to go recheck the voltages again. and the solenoid with the green clip which is right adjacent to the solenoid with the yellow/orangish clip is missing a vacumn line off the top of it, it just has a bare nipple. is this what you thinks throwing the code? ill r...

so ive called all the mazda dealerships they dont have a part prc solenoid or valve, they dont know where it is what it is does and cant answer for me. ive searched and the only hits i get is my questions about it? it was a code 35 i was thinkin maybe code 3 and code 5 but there is no code 5. i dont...

i pulled the codes from my car after having to swap in a new wiring harness and im gettin a code 35 3 long flashes and 5 short. it says prc soelenoid no.2. could this cause the car not to start cause i cant get it running? where is it located? whats its function and how could i remedy this problem?

Okay i pulled the codes its a code 35? 3 long 5 short. it means prc solenoid no.2? what is this solenoid? wheres it located? could this cause it not to start?