Search found 10 matches

by scotland_mx3
July 19th, 2006, 1:48 pm
Forum: European MX-3 Community
Topic: reverse glow dials
Replies: 4
Views: 1849

thanks m8 , i will check them out. :D
by scotland_mx3
July 18th, 2006, 4:50 pm
Forum: European MX-3 Community
Topic: reverse glow dials
Replies: 4
Views: 1849

reverse glow dials

hi, anyone know where to get reverse glow white face dials in the uk ?

seen a few in usa on ebay but they wont accept paypal & shipping seems expensive.

any advice much appreciated.
by scotland_mx3
July 18th, 2006, 1:27 pm
Forum: 4-Cyl. Technical/Performance
Topic: hot starting problem - sorted
Replies: 8
Views: 631

hot starting problem - resolved

problems now sorted , fuel leak with new o rings and the old favourite the coolant temp sensor ! its amazing how much of a problem that sensor can cause , thanks again for your replies. she now runs sweet and is no problem to start. :D :D :D
by scotland_mx3
June 25th, 2006, 12:49 pm
Forum: 4-Cyl. Technical/Performance
Topic: hot starting problem - sorted
Replies: 8
Views: 631

thanks for all your advice, am not using car untill fuel leak sorted, will be going to garage for that so will get codes pulled at same time , will use the test lamp method in the future though. :)
by scotland_mx3
June 25th, 2006, 9:04 am
Forum: 4-Cyl. Technical/Performance
Topic: hot starting problem - sorted
Replies: 8
Views: 631

i have just noticed fuel leaking out of injector on number 2 cylinder , seems to be leaking a fair bit from the o rings , could this cause my hot starting problem ?
by scotland_mx3
June 25th, 2006, 5:52 am
Forum: 4-Cyl. Technical/Performance
Topic: hot starting problem - sorted
Replies: 8
Views: 631

when i say i have no engine light on the dashboard i meant that it does not have one fitted, it would appear the early uk model does not have the light fitted, it has the diagnostic connector under the hood so it looks like a trip to my local mazda dealer to get them to pull the codes.
by scotland_mx3
June 24th, 2006, 1:49 pm
Forum: 4-Cyl. Technical/Performance
Topic: hot starting problem - sorted
Replies: 8
Views: 631

my idle problem seem to stop when i fitted new distributor & ht leads so have not changed the sensor, i have no engine light on the dashboard so do i need to get it plugged into a computer at a garage to get the codes ?
by scotland_mx3
June 24th, 2006, 11:01 am
Forum: 4-Cyl. Technical/Performance
Topic: hot starting problem - sorted
Replies: 8
Views: 631

hot starting problem - sorted

hi, car is a 1992 1.6 sohc auto , uk model, the car starts and runs fine when cold, will run for a good few miles but when hot will die and refuse to start when hot , if i let it cool down for a while it will start up fine again, its been serviced recently, had new ht leads, new distributor cap and ...
by scotland_mx3
June 23rd, 2006, 3:59 am
Forum: 4-Cyl. Technical/Performance
Topic: where is my coolant temp sensor ? uk model
Replies: 2
Views: 217

thanks for the reply , there is a sensor near the 1st & 2nd injectors so that must be the one. it has a green plastic connector on it.

cheers :D
by scotland_mx3
June 22nd, 2006, 2:36 pm
Forum: 4-Cyl. Technical/Performance
Topic: where is my coolant temp sensor ? uk model
Replies: 2
Views: 217

where is my coolant temp sensor ? uk model

hi , this is my first post so hi to all, am looking for my coolant temp sensor to try to sort out my erratic idle problem , car is a 1992 mx3 1.6 16v auto , its not in the same place as shown in the online manual or in my mazda electronic parts catalogue, only thing i can see that looks like it is a...

Go to advanced search