MX-3.com

I have another question, at the workshop manual they use that images to show how to install the camshafts and crankshaft pulleys, like this: http://www.aguiloco.com/distribucion.jpg The crankshaft pulley must be aligned as original image (yellow spot) or must be turned and aligned to the up mark (li...

Hi, you can see my past in that post before begin reading: http://www.mx-3.com/phpbb2/viewtopic.php?t=57792 This is my actual situation: I got a KLZE from Japan to Spain, I swap it to my good running MX3 at a bad garage with a stupid mechanic. The engine don´t run good and something sounds rare at t...

the knock sensor is plugged right, I check the fuel lines too. Did a diagnostic and tell me errors from EGR (norma, I have 3 connector unplugged from it) and O2 left sensor. At thos time I cant get spark, tomorrow the mechanic will check it again and at wendsday I will bring the car to a mazda deale...

PAT, I try it with new spark plugs and used spark plugs, I´m using my old distributor from the k8 that was working good for me before the swap. I try with my wires and with the wires from the ZE. The mechanic says timming is mounted right, but I have to check it with by myself... The ZE has timing m...

Eso mismo es lo que yo pienso! si realmente tuviera algo mal internamente sonaria fatal al hacerlo girar, pero es que suena de maravilla! Es con el motor en marcha cuando suena algo en la parte de la admision, aunque no se que es. El motor se para si dejo de acelerarlo y se ahoga al acelerar tambien...

mejor hablame en español que en ingles me cuesta seguirte. Hay chispa en las bujias y estan colocadas correctamente en el distribuidor. Estoy usando el alternador y distribuidor del k8. Si el motor tubiera algun problema en las valvulas o cigüeñal al hacerlo girar sin las bujias como te he dicho las...

PWRD I do the engine run without spark plugs using the start electrical engine of the car (as usually you start an engine), compresion go out of each spark hole and that "cla cla cla cla..." dont sound. the sound is when the engine is runing with all connected.

Is hard to see that valves?

PLEASE HELP ME!!! that´s the actual situation: The mechanical says than the engine is in bad shape because at the intake maniford something sounds like a valve clicking continuos and the general run of the engine is really rare. I think that is possible than that man didn´t mount the engine right. I...

el motor no funciona bien, hace un ruido muy raro como de valvulas en la parte de la admision y tiembla mucho. Puede ser que me hayan puesto mal la correa de distribucion pero no lo puedo demostrar por el que mecanico dice que la puso como estaba la anterior. Si me mandas fotos me ayudarias mucho en...

forget it, the engine finally start, but sound bad, too bad, and the vibrations are really anormal...

buf.... really I speak english only the basic, when you start talking about technicall parts without images is a kick in my a-- to understand all... actually the car won´t start, have problems at the sparks, maybe in vacuum too... Only using another cable to connect negative to the engine block the ...

is that the vacuum diagram from the k8 right solo_rider? for the millenia IM would be the same but without the EGR system?

mazdamx3freak I cant see your image...

hi, I´m finishing the SWAP but have to check all the vacuum lines for the millenia IM.

I search at the forum but all the topics with diagrams has broken links or non displayed images...

A lot of good photos of a working swap will help me too

thanks a lot

if is the same belts I will get it tomorrow with my chassis number at Mazda dealer.

Thanks a lot!

hello, I will start my SWAP next Monday and only need the belts for AC, generator, etc... At the dealers I cant take the belts because they only spend parts with chassis numbers... At the forum I can´t see the size of that belts using search... The KLZE use the same belts size as the K8 or the 2.5 p...