Looking good.
What wheels are those? Love the sound.
Now give that KLZE a new home.
Where are your GS spoiler?
anyway looks great.
Odds
OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
Odds, Norway
Red `93 GS, Stock
Red `93 GS, Stock
- wyldside
- Supporting Member
- Posts: 1364
- Joined: February 2nd, 2002, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Cheadle, Alberta, Canada
- Contact:
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
Just to warn you, the ignitor module will eventually die again. Those replacement distributors are usually manufactured by Mitsubishi and the ignitor modules inside them can't handle the heat from our engines. You might be better off doing the MSD conversion with the MSD 6A and Blaster 2 Coil when you put in your ZE.
James Gosteli
X-Prez of MX-West
1992 Seal-Gray MX-3 GSR-ZE (KLZE 2.5L V6)
1992 White MX-3 GSR-ZE (KLZE 2.5L V6) Worklog (Parting out)
1993 Blaze Red MX-3 GS - RIP
X-Prez of MX-West
1992 Seal-Gray MX-3 GSR-ZE (KLZE 2.5L V6)
1992 White MX-3 GSR-ZE (KLZE 2.5L V6) Worklog (Parting out)
1993 Blaze Red MX-3 GS - RIP
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
kool, hope to see ya crusing around
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
- MX3-Freak
- Regular Member
- Posts: 955
- Joined: November 8th, 2003, 2:01 am
- Location: Gig Harbor Washington
- Contact:
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
You willing to sell your GS spoiler? Just asking because I like the looks fo it betterOriginally posted by XxAntwawnxX:
Thanx, took the gs spoiler off and put the 4banger hatch garnish on..i like the looks of it better, and im in the market for a diff wing(nothing crazy dont worry) those are konig rated R's
Stock 1995 RS - Creek Blue
Car Meanins:
Honda: Hang On, Not Done Accelerating
FORD: Frequently Overhauled, Rarely Driven
Mazda: Must Always Zoom Down Asphalt
Car Meanins:
Honda: Hang On, Not Done Accelerating
FORD: Frequently Overhauled, Rarely Driven
Mazda: Must Always Zoom Down Asphalt
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
looks nice, ya id just return all those disty's and get MSD or mallory disty with control box
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
are those konig's 17's or 18's ive got 18's white ones and wondered if theyd look same on my car.
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
-
- Regular Member
- Posts: 365
- Joined: September 18th, 2001, 2:01 am
- Location: Okinawa, Japan
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
Ya I got his gs spoiler. Didn't buy it, me and him traded. I gave him my hatch garnish for his spoiler. Anyway. Antwan do you have your other turn signal? The one I got from you is for the passenger side. I need the driver side.
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: OMG I FINALLY FIXED MY BABY...ohman its been so long (VI
i got a pair of turn signals i dont need someplace here
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy