I guess I haven't updated this thing in a while.
These are probably going to be out of order. But here's a bunch of pics with some upgrade listing below. (And probably already seen them if you're on facebook)
This is right after I lowered it, next to a beast. The springs hadn't settled yet.
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592291)
Chalkboard paint never grows old.
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592294)
Sitting low, with a GS lip. I like this picture a lot.
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592296)
Who needs a truck? (returning a core trans for my dad)
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592297)
After failed hood struts, I went topless for a while.
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592299)
Josh gave me the hood off his AWD MX-3
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592298)
How the car sits right now...
=========================================================================
Parts install pics
=========================================================================
Rear KYB GR2s with B&G springs
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592293)
Front KYB GR2s with B&G springs
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592295)
Energy Suspension bushings all the way around (Front LCAs, rear trailing arms, rear lateral links)
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592292)
Brand new Whiteline rear swaybar Solid 22mm
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592300)
Ford ZX2 tubular trailing arms
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592301)
More bushings, Moog strut bellows/bumpstops, Moog strut tophats, Moog inner/outer tie rod ends, Moog ball joints, Moog spring seats
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592302)
Complete GS rear subframe. I'm waiting on new pads and rotors. I'm currently installing the Energy Suspension TTL bushings and swapping over the Whiteline sway bar.
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592305)
String line alignment after I installed the wider RX7 ball joints to alleviate some axle issues
=====================================================================
Parts that I've installed
=====================================================================
Okay, I hope I remember it all
I went through the entire suspension and underside of the car.
B&G springs
KYB GR2 struts
Moog:
Strut tophats K8995
Bellows K90464
Bump Stops (same part # above)
RX7 Ball joints K9427 (Stock Moog MX-3 Balljoints part #K9967)
Spring seats K8995
Swaybar endlinks (front and rear)
Energy Suspension bushings:
ZX2 trailing arm bushings 4.7123G
LCA bushings (Need ZX2 rear carrier) 4.3152G
TTL bushings 9.9108G
94+ knuckles (to fit the RX7 ball joints)
GS rear subframe
Slotted rear rotors
Ceramic brake pads (front/rear)
Whiteline 22mm swaybar (bushings too)
GS Rear lower tie bar
OBX Upper rear strut tie bar
Ebay Upper front strut tie bar
Inner and outer tie rod ends
Still rocking a NA BP05, with an F5M-R tranmission.
I think I need to work on the engine now...
And my GS, waiting for a new crank...
![Image](http://www.pix8.net/pro/pic.php?u=2838Ipxto&i=11592303)