Drewhall07's BP/Turbo Mx-3 Build thread
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Drewhall07's BP/Turbo Mx-3 Build thread
Ok, First off Hello everyone.This is my first Real post on here besides my introduction.lol Anyways, got my first mx3 tonight. its a 92 mx3 gs auto v6. The car has been sittin the last 2 yrs and has only had 2 owners, and now me.
165k on the speedo
drilled rotors
SS brake lines
K&N air filter
Tokico struts(gotts check to see if there real)
Magnaflow exhaust(which i doubt is real to)
16' rims
this is wat was told to me. i will get a better look at things 2mrrw as i start strippin stuff off the car. interior is VERY clean. but does need a good washin as it has that old wet smell kinda to it. But neways, enough talkin, on wit pics.
Still has the owners manuel..lol
Pumpin the tires up, gettin rdy to be put on the trailer
Front end was under a tree for 2 yrs, so its DIRTY..lol
Slammed in the front
Gettin her on the trailer
Come on u bish, almost there
On the trailer finally. lol
Finally got her to the shop. where she will be for the next few months.
Lil shot under the hood.
And a few of the Escort
Overall, i think the car is in great shape. havent found any rust spots yet but that will proly change once i dig deeper into this project. Sum of my plans are as follows:
Engine/Drivetrain:
bp05 swap
gt trans
t25/t28 turbo
rx7 460cc injectors
rx7 vaf
Fidanza Cam Gears
Fidanza 8lb flywheel
AEM Wideband
HKS ssqv bov
FMIC with 2.5 piping
stage 3 6-puck clutch
new headgasket
new thermostat
new plugs
new wires
new intake mani gasket
new exhaust mani gasket
new VC gasket
new oil pan gasket
oil/water line kit for turbo
GTR intake mani
new racing motor mounts
new throw out bearing
new pilot bearing
Suspension:
Tokico Struts
Lowering Spring
ES master bushin kit
Corksport Strut tower bars
Corksport SS brake lines
Corksport SS clutch line
Interior:
Dye carpet black
Paint interior black/grey
New racing seats
new headunit
new speakers all around
Indiglo HVAC gauges
reverse glow cluster
Custom Gauge pod
Misc:
HID headlights
New Headlight lenses
New tires
Tint
Prof wash/wax job
touch up paint chips
Clean engine bay
Paint engine bay glossy black
replace winshield
Well thats all i can think of right now. but i will be posting more pics 2mrrw as i will start the dissasemble of the car and get it rdy to start the transplant from v6 to 4cyl turbo. Lemme kno what u guys think of the car. Love questions and comments.
Thanks,
Drew
165k on the speedo
drilled rotors
SS brake lines
K&N air filter
Tokico struts(gotts check to see if there real)
Magnaflow exhaust(which i doubt is real to)
16' rims
this is wat was told to me. i will get a better look at things 2mrrw as i start strippin stuff off the car. interior is VERY clean. but does need a good washin as it has that old wet smell kinda to it. But neways, enough talkin, on wit pics.
Still has the owners manuel..lol
Pumpin the tires up, gettin rdy to be put on the trailer
Front end was under a tree for 2 yrs, so its DIRTY..lol
Slammed in the front
Gettin her on the trailer
Come on u bish, almost there
On the trailer finally. lol
Finally got her to the shop. where she will be for the next few months.
Lil shot under the hood.
And a few of the Escort
Overall, i think the car is in great shape. havent found any rust spots yet but that will proly change once i dig deeper into this project. Sum of my plans are as follows:
Engine/Drivetrain:
bp05 swap
gt trans
t25/t28 turbo
rx7 460cc injectors
rx7 vaf
Fidanza Cam Gears
Fidanza 8lb flywheel
AEM Wideband
HKS ssqv bov
FMIC with 2.5 piping
stage 3 6-puck clutch
new headgasket
new thermostat
new plugs
new wires
new intake mani gasket
new exhaust mani gasket
new VC gasket
new oil pan gasket
oil/water line kit for turbo
GTR intake mani
new racing motor mounts
new throw out bearing
new pilot bearing
Suspension:
Tokico Struts
Lowering Spring
ES master bushin kit
Corksport Strut tower bars
Corksport SS brake lines
Corksport SS clutch line
Interior:
Dye carpet black
Paint interior black/grey
New racing seats
new headunit
new speakers all around
Indiglo HVAC gauges
reverse glow cluster
Custom Gauge pod
Misc:
HID headlights
New Headlight lenses
New tires
Tint
Prof wash/wax job
touch up paint chips
Clean engine bay
Paint engine bay glossy black
replace winshield
Well thats all i can think of right now. but i will be posting more pics 2mrrw as i will start the dissasemble of the car and get it rdy to start the transplant from v6 to 4cyl turbo. Lemme kno what u guys think of the car. Love questions and comments.
Thanks,
Drew
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
ok, not much to say 2day, just more pics in the daylight from before and after i gave her a wash. Got wat i could off, but sum stuff is stuck on the car..lol
Before the wash
After 2 hours of scrubbing and washing the car
Interior needs cleaning, will do later
Seats r to dang clean to be a 92..lol
165k on the odo
Well thats all for now. gonna start taking the motor/tranny out maybe 2mrrw or monday. and im gonna get the auto trans fixed for now, till i can get everything i need to do the entire swap within a few days, instead of piecing everything 2gether here and there. also gonna keep the paint white, just gonna get it repainted the stock paint color. carpet will be dyed black, and maybe gonna paint the interior, but idk yet.
Lemme kno what u guys think. love questions and comments.
Thanks,
Drew
Before the wash
After 2 hours of scrubbing and washing the car
Interior needs cleaning, will do later
Seats r to dang clean to be a 92..lol
165k on the odo
Well thats all for now. gonna start taking the motor/tranny out maybe 2mrrw or monday. and im gonna get the auto trans fixed for now, till i can get everything i need to do the entire swap within a few days, instead of piecing everything 2gether here and there. also gonna keep the paint white, just gonna get it repainted the stock paint color. carpet will be dyed black, and maybe gonna paint the interior, but idk yet.
Lemme kno what u guys think. love questions and comments.
Thanks,
Drew
- WhiteFinish
- Regular Member
- Posts: 1635
- Joined: April 3rd, 2006, 9:48 am
- Location: Netherlands
- Contact:
Re: Drewhall07's BP/Turbo Mx-3 Build thread
Nice job on the cleaning !!
I have never seen an mx with a different colour plastic panals/dash.
I have never seen an mx with a different colour plastic panals/dash.
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
well didnt get to much done 2day, as its real muggy and kept rainin off n on. but i did get the rad/fans out, exhaust unhooked, intake system off, old security system out, ps unhooked, batt out, lots of sensors unhooked, and a few other things. hopefully ill be able to pull the motor n trans 2mrrw. and start pulling the unnessacary stuff out, diff wires, ac componets, and just w.e im not gonna use over. well heres the only 2 pics i could get as it was rainin and didnt wanna ruin my camera.
Seeing as if i get the motor/trans out 2mrrw. and get all the lil things pulled, im gonna soak the bay down with degreaser, clean it up real good, and gonna primer it, and go with a high gloss black for the bay. But neways, lemme kno what u guys think.
Thanks,
Drew
Seeing as if i get the motor/trans out 2mrrw. and get all the lil things pulled, im gonna soak the bay down with degreaser, clean it up real good, and gonna primer it, and go with a high gloss black for the bay. But neways, lemme kno what u guys think.
Thanks,
Drew
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
ok, well heres the only 2 pics i could grab 2day while i got the motor n stuff out..
tomorrow i will start takin the lil things out that i dont need/want.. and im bout to make a forsale thread with some stuff... go buy ppl..lol
Also, the crossmember that runs from side to side, can i reuse that bar? and will it work on the escort also??
Thanks,
Drew
tomorrow i will start takin the lil things out that i dont need/want.. and im bout to make a forsale thread with some stuff... go buy ppl..lol
Also, the crossmember that runs from side to side, can i reuse that bar? and will it work on the escort also??
Thanks,
Drew
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
ok well, just wanted to add a few pics of everything i have so far in case noone remembers from my egt turbo build..lol
Turbo mani, turbo, and downpipe
Real HKS ssqv bov
Greddy Turbo Timer
Gauge Pod
Boost Gauge
Custom exhaust made for the turbo
GT tranny, gonna be cleaned and painted
Stage 3 6-puck clutch
Intercooler
RX7 vaf
OEM mazda headgasket
Fidanza Cam gears
Intercooler piping
PS cooler for relocation
AEM Wideband
SS brake lines
SS clutch line
Walboro 255lph fuel pump
lil bit of everything
Well thats bout all i have right now. im still collecting stuff. Thats why im tryin to sell alota stuff so i can finish gettin everything for the turbo..
Things i still need:
Fidanza flhywheel
rx7 injectors
Racing Motor Mounts
Half rad and slim fan
ARP head and main studs
GTX cams
Boost Controller
FPR
GTR Intake mani
Gates Racing Timing Belt
Fidanza Short Shifter
MegaSquirt(in the future. lol)
i think thats all, but may be wrong..lol Thanks for lookin. love questions and comments.
Thanks
Drew
Turbo mani, turbo, and downpipe
Real HKS ssqv bov
Greddy Turbo Timer
Gauge Pod
Boost Gauge
Custom exhaust made for the turbo
GT tranny, gonna be cleaned and painted
Stage 3 6-puck clutch
Intercooler
RX7 vaf
OEM mazda headgasket
Fidanza Cam gears
Intercooler piping
PS cooler for relocation
AEM Wideband
SS brake lines
SS clutch line
Walboro 255lph fuel pump
lil bit of everything
Well thats bout all i have right now. im still collecting stuff. Thats why im tryin to sell alota stuff so i can finish gettin everything for the turbo..
Things i still need:
Fidanza flhywheel
rx7 injectors
Racing Motor Mounts
Half rad and slim fan
ARP head and main studs
GTX cams
Boost Controller
FPR
GTR Intake mani
Gates Racing Timing Belt
Fidanza Short Shifter
MegaSquirt(in the future. lol)
i think thats all, but may be wrong..lol Thanks for lookin. love questions and comments.
Thanks
Drew
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
Got summore work done on the car today. took alot more stuff out the bay that i wasnt gonna need. sprayed the bay down with purple power, let it soak, rinsed off, sprayed it down again, scrubbed the real dirty areas, and found that parts that i didnt even kno they was suppose to be white...lol anyways heres a few pics
Before i started cleanin the bay up
After the soak downs n wash
Most of the stuff ive taken out, besides the motor/trans and the stuff im selling
and the car had a nice PS cooler on it, gonna reuse this one..lol
Thats all for 2day. didnt get the bay as clean as i want it but looks hella better than it did. lol still decidin if i wanna paint the bay glossy black or leave it like it is, but i do want a clean lookin bay, and dirt wont show as bad on a black bay... hmmm Anyways, i may start sprayin primer on the bay 2mrrow if i feel like it, or start takin the interior out and gettin it all clean and dye the carpet black. and also try and fix the leak from the damn moonroof. XD Lemme kno what u guys think.
Thanks,
Drew
Before i started cleanin the bay up
After the soak downs n wash
Most of the stuff ive taken out, besides the motor/trans and the stuff im selling
and the car had a nice PS cooler on it, gonna reuse this one..lol
Thats all for 2day. didnt get the bay as clean as i want it but looks hella better than it did. lol still decidin if i wanna paint the bay glossy black or leave it like it is, but i do want a clean lookin bay, and dirt wont show as bad on a black bay... hmmm Anyways, i may start sprayin primer on the bay 2mrrow if i feel like it, or start takin the interior out and gettin it all clean and dye the carpet black. and also try and fix the leak from the damn moonroof. XD Lemme kno what u guys think.
Thanks,
Drew
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
Went to Ford 2day and got new Teflon orings so when i put the gt ps lines into the mx3. Also cleaned the bay up a lil more, removed sum more stuff, and also put a coat of primer over the bay. gonna put another coat 2mrrw, then start throwin the black on proly fri and sat. Also got the whole bottom half of the dash apart, took the auto shifter out, and sum other things... gonna try and start takin the pedals and **** out 2mrrw. well on to sum pics
Few more of the car after takin more stuff out u can barley notice tho
Inside
Stuff im keepin to paint black
Seat covers im gonna wash, then get the MX-3 stiched red with black outline
maybe the floor mats too..lol
And a few pics to let yall see the seats.. =P Look but dont touch fools
Tokico Struts all the way around, tried to get a pic of the p/n but cam couldnt catch it. they the older model struts
Lil primer on the bay, was gettin dark, hope u can see
And can sumone tell me what this box if for?? its says K802 2C09
Well thats all i have for right now.. lemme kno what u guys think.
Thanks
Drew
Few more of the car after takin more stuff out u can barley notice tho
Inside
Stuff im keepin to paint black
Seat covers im gonna wash, then get the MX-3 stiched red with black outline
maybe the floor mats too..lol
And a few pics to let yall see the seats.. =P Look but dont touch fools
Tokico Struts all the way around, tried to get a pic of the p/n but cam couldnt catch it. they the older model struts
Lil primer on the bay, was gettin dark, hope u can see
And can sumone tell me what this box if for?? its says K802 2C09
Well thats all i have for right now.. lemme kno what u guys think.
Thanks
Drew
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
i wasnt able to update like i wanted so all those post r from where i posted at CP, just copied and pasted... enjoy
Re: Drewhall07's BP/Turbo Mx-3 Build thread
ahhhhh your sooo lucky....can't wait til i rip my motor out!! but it still runs strong. so im focusing on the PAINT..... keep it up! ill be keeping my eye on this blog. ah ecu?
___________________
Black '92 GS [Project De-t Started!] [The spoiled one]
Green '95 1.6 [Daily][The jealous one...SOLD]
White '07 Mazda 3 GT [The pretty one]
[What can you say, I have a fetish for 3's]
Black '92 GS [Project De-t Started!] [The spoiled one]
Green '95 1.6 [Daily][The jealous one...SOLD]
White '07 Mazda 3 GT [The pretty one]
[What can you say, I have a fetish for 3's]
mikeetown wrote: Do what you want to do dude cause in the end, your mx-3 is all about you.
- WhiteFinish
- Regular Member
- Posts: 1635
- Joined: April 3rd, 2006, 9:48 am
- Location: Netherlands
- Contact:
Re: Drewhall07's BP/Turbo Mx-3 Build thread
Yep, it's your ECU for the 1.8 v6 engine
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
i dnt think its the ecu cuz i alrdy took 1 ecu out when i ripped the engine harness out... but i could be wrong... just wondering if i can trash it or notWhiteFinish wrote:Yep, it's your ECU for the 1.8 v6 engine
- drewhall07
- Regular Member
- Posts: 34
- Joined: October 27th, 2009, 10:31 pm
- antispam: No
Re: Drewhall07's BP/Turbo Mx-3 Build thread
well small update 2day. Put another coat of primer on the bay, let it dry for a few hours then, thru-out the day, i put 2 coats of high-temp, rust resistant gloss black. might throw one more coat on it 2mrrw, depends how it looks when i go up there and see it in the sunlight. but neways, heres a few pics
Final coat of primer
Two coats of black
Ill proly have to go back and hit a few spots that im sure i missed. like the inner fender parts and stuff, didnt wanna take the fenders off so ehh.. but neways, lemme kno what u guys think so far
Thanks,
Final coat of primer
Two coats of black
Ill proly have to go back and hit a few spots that im sure i missed. like the inner fender parts and stuff, didnt wanna take the fenders off so ehh.. but neways, lemme kno what u guys think so far
Thanks,
Re: Drewhall07's BP/Turbo Mx-3 Build thread
awsome worklog great work keeping my on on this
92' Red GS - RIP
93' Black Miata LE
93' Black Miata LE
-
- Regular Member
- Posts: 576
- Joined: March 24th, 2002, 2:01 am
- Location: Stellarton, Nova scotia, Canada
- Contact:
Re: Drewhall07's BP/Turbo Mx-3 Build thread
That box under your stereo area is your automatic tranny ECU.