[WTB] ATX for my 94 GS

JHetfield · Post by **JHetfield** » May 23rd, 2006, 5:43 pm

anyone please...I know some of you guys have these just laying around after your MTX swaps. if someone has one that is still in good shape, and aren't too far away/willing to ship. let me know please, cause mine is done

thanks

jschrauwen · Post by **jschrauwen** » May 23rd, 2006, 6:07 pm

JHetfield wrote:anyone please...I know some of you guys have these just laying around after your MTX swaps. if someone has one that is still in good shape, and aren't too far away/willing to ship. let me know please, cause mine is done
thanks

Shipping is not going to be cheap. Those that did a swap to MTX probably did it because the ATX was toast or close to it. I couldn't really see someone swapping out a completely serviceable and perfectly functioning ATX. That said, if your willing to try and acquire an ATX from one of the Eunos800 (ZE)'s that may be had for a good price from an importer since they are not the most popular tranny's for them. I believe that Tiger Japanese in Toronto would still have at least 4 or 5 ZE ATX's kicking about if not more. The added spin to this is, is that you'd be getting an extremely low mileage ATX. The other option would be an ATX rebuild that would most assuredly cost 3 to 4 times more than one of those ZE ATX's. Just food for thought for you. If I were running an ATX, that would be the route that I would take. Any tranny shop that even wants to crack the tranny cases open on an ATX is going to be asking at least 1,500 to 2,000 cdn for the repair work.

ariesdude · Post by **ariesdude** » May 23rd, 2006, 6:20 pm

Try mazda dealer - you might get one for less than the cost of a rebuild....

http://www.mx-3.com/phpbb2/viewtopic.php?t=50310

JHetfield · Post by **JHetfield** » May 23rd, 2006, 10:33 pm

will Tiger Jpn's ATX fit my 1.8L? and do they have a website?

thanks

JHetfield · Post by **JHetfield** » June 21st, 2006, 4:44 pm

anyone?

ariesdude · Post by **ariesdude** » June 21st, 2006, 10:20 pm

JHetfield wrote:will Tiger Jpn's ATX fit my 1.8L? and do they have a website?

thanks

Dont know if it will fit or not - but here's some info about the company
http://www.mx-3.com/phpbb2/viewtopic.ph ... highlight=

Tunes67 · Post by **Tunes67** » June 22nd, 2006, 12:08 pm

Ok.. I am almost capable of shipping my old GS ATX. It has 92k Miles on it and seemed to shift fine before I pulled it. However.. the fluid was pretty dark. So I doubt this tranny had much prior maintenance. Now I have drained the fluid completely from both the trans and the torque converter. I wont charge a lot for it since there is no telling how long it will last. $150 + Shipping and you figure out how to get it shipped LOL My zipcode is 98203

Tunes67

ProspectMx3 · Post by **ProspectMx3** » June 22nd, 2006, 6:58 pm

I,ve got a ATX tranny from my ZE (Eunos800), that has approx 40,000miles on it. $300 +shipping.

JHetfield · Post by **JHetfield** » June 23rd, 2006, 12:55 pm

no one has yet to confrm that the ATX from the Eunos 800 will fit a stock GS...if its a KLZE ATX, then are we not all in agreement that it will not?

MX-3.com

[WTB] ATX for my 94 GS

[WTB] ATX for my 94 GS

Re: [WTB] ATX for my 94 GS