shortened auto shifter
shortened auto shifter
can anyone point me toward the thread on shortening an auto shifter. I've seen it before...but can't seem to find it, I've done 20 searches...
-94 GS 1.8L Black
-69 Pontiac Firebird 400 Turbo
-69 Pontiac Firebird 400 Turbo
nope...there was a thread I saw about 2 months ago on shortening (cutting) the footlong shaft that is our automatic shifter rods...but I found it finally...I searched "hacksaw" LOL...
however no one on that thread gave very detailed instructions on how to do it...everyone there just replaced their stock knobs with aftermarket, but I want to shorten the rod and keep my stock knob with the hold button.
however no one on that thread gave very detailed instructions on how to do it...everyone there just replaced their stock knobs with aftermarket, but I want to shorten the rod and keep my stock knob with the hold button.
-94 GS 1.8L Black
-69 Pontiac Firebird 400 Turbo
-69 Pontiac Firebird 400 Turbo
Well the first thing you need to do is take it out. Then find a spot where to cut it then make a nice clean cut. THen you need to find out what thread the shift knob is. After that you need to re-thread the shifter so you can screw on the knob. Then put it back in your car and it should work fine.
1994 toyota supra single turbo
1994 Mazda MX-3 KL-ZE
If god owned a car... It would be a supra!!!
1994 Mazda MX-3 KL-ZE
If god owned a car... It would be a supra!!!
- Tunes67
- Supporting Member
- Posts: 4708
- Joined: January 27th, 2005, 6:36 pm
- Location: Everett, WA
- Contact:
Could always try my solution Swap out the ATX and put in a MTX A bit more work though
Tunes67
Tunes67
"So long.. and thanks for all the fish!" "Momma says VW Bugs are the devil" "This one time at band camp.. I stuck a flute in my Throttle Body"
"Screw you guys.. I am goin home"
I am the Cranky God of Mods!!! Tremble before my fury!! LOL
"Screw you guys.. I am goin home"
I am the Cranky God of Mods!!! Tremble before my fury!! LOL
that was my inital plan at the beginning of winter...my hold light was flashing so I assumed it was time. put the battery back in a couple days ago, and been driving and no light, so I was going to wait and swap when my ATX blew up...trying to get 30 posts so I can post a WTB for a K8 manual, man its hard to post new stuff on here tho, so many problems are answered by searching
-94 GS 1.8L Black
-69 Pontiac Firebird 400 Turbo
-69 Pontiac Firebird 400 Turbo
- Tunes67
- Supporting Member
- Posts: 4708
- Joined: January 27th, 2005, 6:36 pm
- Location: Everett, WA
- Contact:
man its hard to post new stuff on here tho, so many problems are answered by searching
LMAO We got us a winner guys!!! Dude if you were local to me I would buy you a steak dinner for that one As for your hold light going off.. well when you removed the battery.. it cleared the code from the TCM after sitting with no power for so long. Depending on the code.. it will likely show up again... you can pull the ATX codes (once the light starts flashing) by jumping TAT and GND in the diagnostic box along the firewall on the drivers side of your engine bay. And in a couple of months... my GS will be a MTX. The ATX's in these cars are way too problematic.. but thats to be expected since Ford designed them. If the trans seems to be shifting fine, and isnt slipping at all.. likely its just a code 6 which is a speedometer speed sensor. That one trips in my GS every time I take the car up past 80 mph. Dunno why.. doesnt seem to hurt anything.. just gotta clear the code every once in a while. Oh and I checked on it for price.. mazda only part.. $159.00 + tax.. I figured I would save the $$$ and put it towards the MTX parts. Cheers and welcome to the board
Tunes67
"So long.. and thanks for all the fish!" "Momma says VW Bugs are the devil" "This one time at band camp.. I stuck a flute in my Throttle Body"
"Screw you guys.. I am goin home"
I am the Cranky God of Mods!!! Tremble before my fury!! LOL
"Screw you guys.. I am goin home"
I am the Cranky God of Mods!!! Tremble before my fury!! LOL