hey guys, i'm doing a KL swap on my 1991 protege GT (BP powered) and i was wondering if anyone ran into the speedogear @ the tranny side, i heard it wont fit properly and someone made a spacer on this site??? if so could you post pics or specs of this spacer???
thanks
JACK
BP speedogear on a K8 tranny???
-
- Regular Member
- Posts: 174
- Joined: November 3rd, 2005, 1:31 am
BP speedogear on a K8 tranny???
.::Mazda::speeD::.
working on the 2nd part![Wink ;)](./images/smilies/icon_wink.gif)
working on the 2nd part
![Wink ;)](./images/smilies/icon_wink.gif)
- kiwi_MX3
- Regular Member
- Posts: 736
- Joined: August 10th, 2004, 2:01 am
- Location: Backpacking in Canada in vancouver 13march onwards
- Contact:
Im afraid your going to have to be a little more precis about your
question, for a start what motor to what gearbox are you fitting
definitly not the BP box back in.
And where abouts are you trying to fit the speedo???
question, for a start what motor to what gearbox are you fitting
definitly not the BP box back in.
And where abouts are you trying to fit the speedo???
Kiwi - Native Bird Of New Zealand, semi-nocturnal, secretive bird
Flightless, though can be found flying firstclass
Poor eyesight, though can spot a good pub at 100yards.
Flightless, though can be found flying firstclass
Poor eyesight, though can spot a good pub at 100yards.
-
- Regular Member
- Posts: 174
- Joined: November 3rd, 2005, 1:31 am
i'm putting a KL03 2.5 V6 24 Valve DOHC into my 1991 Mazda Protege GT which currently has a BP 1.8 L4 16 Valve DOHC. ok?
So on that note, im using a K8 Transmission like stated in the Title of this post bolted to the KL03 engine!
Now onto the things that matter! i'm using the BP 1.8 speedcable, and im going to attempt to bolt it into THE TRANSMISSION OF THE K8.
I heard somebody in this site made an apapter/spacer so its possible for me to bolt the protege speedcable into the K8 Transmission, does anyone have pics or recollection of this event????
JACK
So on that note, im using a K8 Transmission like stated in the Title of this post bolted to the KL03 engine!
Now onto the things that matter! i'm using the BP 1.8 speedcable, and im going to attempt to bolt it into THE TRANSMISSION OF THE K8.
I heard somebody in this site made an apapter/spacer so its possible for me to bolt the protege speedcable into the K8 Transmission, does anyone have pics or recollection of this event????
JACK
.::Mazda::speeD::.
working on the 2nd part![Wink ;)](./images/smilies/icon_wink.gif)
working on the 2nd part
![Wink ;)](./images/smilies/icon_wink.gif)
- kiwi_MX3
- Regular Member
- Posts: 736
- Joined: August 10th, 2004, 2:01 am
- Location: Backpacking in Canada in vancouver 13march onwards
- Contact:
first off your going to need to get the teeth count on the
speedo gear right as there are variation's for final drives.
I have fitted a Autometer Speedo that uses one of the ABS
sensors to get aorund this problem.
I can't remeber if the BP is cable drive or electronic for the
speedo
speedo gear right as there are variation's for final drives.
I have fitted a Autometer Speedo that uses one of the ABS
sensors to get aorund this problem.
I can't remeber if the BP is cable drive or electronic for the
speedo
Kiwi - Native Bird Of New Zealand, semi-nocturnal, secretive bird
Flightless, though can be found flying firstclass
Poor eyesight, though can spot a good pub at 100yards.
Flightless, though can be found flying firstclass
Poor eyesight, though can spot a good pub at 100yards.
-
- Regular Member
- Posts: 174
- Joined: November 3rd, 2005, 1:31 am
hey, i know you can fit the speedogear in the tranny, because someone did it on clubprotege and it worked. but it wasnt a good fit. they said someone on mx-3.com made up an adapter to fit it in there properly...i was just wondering if anyone know who this was or what this adapter looks like.
JACK
JACK
.::Mazda::speeD::.
working on the 2nd part![Wink ;)](./images/smilies/icon_wink.gif)
working on the 2nd part
![Wink ;)](./images/smilies/icon_wink.gif)