help! wheel bearing
help! wheel bearing
okay.. my back wheel bearing(s) are shot..
its the back right one im pretty sure
question is, how do you figure out which bearing it is? inner or outter.. or do you just buy a whole new assembly?.
Second question, I have ABS.. but the damn wheel bearing is apparently twice as much, I dont use abs.. can I get a standard wheel bearing? or should it be like putting a square peg in a round hole.
Third...wheres the cheapest place in canada to order these from? whats the mazda dealer charge?
its the back right one im pretty sure
question is, how do you figure out which bearing it is? inner or outter.. or do you just buy a whole new assembly?.
Second question, I have ABS.. but the damn wheel bearing is apparently twice as much, I dont use abs.. can I get a standard wheel bearing? or should it be like putting a square peg in a round hole.
Third...wheres the cheapest place in canada to order these from? whats the mazda dealer charge?
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: help! wheel bearing
You should have just one in the spindle.
Id suggest going and buying a spindle from the Junk yard that has a good bearing. I paid 25 for mine. A new bearing is ~ 30-40 bucks I think and you still have to have it pressed in.
Id suggest going and buying a spindle from the Junk yard that has a good bearing. I paid 25 for mine. A new bearing is ~ 30-40 bucks I think and you still have to have it pressed in.
Re: help! wheel bearing
what about the ABS issue?
does it need to be a ABS wheel bearing or will a standard one fit?
does it need to be a ABS wheel bearing or will a standard one fit?
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: help! wheel bearing
To be honest I ve never seen ABS on an MX-3. I know its an option, but noone locally has it. Where is the sensor located for it? I know its near the axle because the Axle has the extra gear for the ABS on it. Got a camera so u can take a pic of the spindle/ABS setup?
Re: help! wheel bearing
dont have a digital camera unfortunatly, yeah ABS is a pain in the rear.. its more harmful then good I'll call a junkyard and see if they have any, but if I need ABS wheel bearings chances are they will have to be ordered. One store wants 140$ for one . But you said there is only one right? I thought there was two.
Re: help! wheel bearing
Been awhile since I had them replaced but I think it was ~200ish cnd at the dealership parts and labor a piece.
<small>[ June 14, 2004, 03:07 PM: Message edited by: Golliwog ]</small>
<small>[ June 14, 2004, 03:07 PM: Message edited by: Golliwog ]</small>
-Golli
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: help! wheel bearing
As far as I know you have one in each spindle of each wheel.
Re: help! wheel bearing
I have the same prob up on the front drivers side.... (dum dum question) is it called a spindle in the front as well?? Looking for it in a junk yard....
-
- Junior Member
- Posts: 22
- Joined: April 28th, 2004, 2:01 am
- Location: Calgary, AB
Re: help! wheel bearing
i just had to replace the wheel bearing on the front passenger side of my 92 GS. Theres only one bearing, i managed to get it for 40 something from lordco parts, and i had to get it pressed in at the dealer which cost me about $30 with taxes. so if priced are comparable there to they are here itll run you about $70-80 canadian if u pull it all apart yourself. plus around $7-10 more for the dust seal