MX-3.com

I was interested in swapping my rack for a gs from my rd

Can I reuse my inner and outer tie rods? (Not to say I'm going to be)
are the parts interchangeable because this rack doesn't have any inner or outer on it

I checked all the fuses I got the relay I can't seem to find it I'm going to temporarily fix it but I would like to know the location of the relay so I can see if that is the problem

Oh the sensor was bad it so it was all green s--- all over it on both the connector on the sensor Now my signal wire wont start the starter I'm just going to run a momentary switch from the battery to the starter for now I got the relay and I looked at all the fuses but I can't find the relay all th...

But I do have a question it won't harm the system if I put the wires backwards to the sensor right it just won't work as long as I know it doesn't do damage if I connect it incorrectly I won't have a problem I just want to be sure because the sensor plug was cut off

Yeah I realized that after I went to look the connection was all green so I was going to cut it and redo it but it broke so I'm going to replace the sensor and try to find a way to make it so it doesn't break

So my reverse lights don't work so for temporary use I want to tap into an earlier point in to my reverse lights system in order to get the lights to work temporarily so I can pass inspection because its urgent If someone can let me know where I can take the positive feedback from whether it be a li...

So I have a 93 mx3 rs ,l1.6 I have no check engine light to make a long story short I have replaced the fuel pump fuel filter fuel injectors fuel pressure regulator I have replaced the distributor cap and rotor plugs and wires I have an MSD blaster ignition coil And as for the air I have the simple ...

i have to agree the US its really really hard to find ANYTHING for my SOHC now, if you CAN find a junkyard one thats good or ebay thats good id get the part if not then id resort to makeshift something, it sucks to do but sometimes you can make things better then the manufacture.

yeah i have 2 inch on the civic with straight pipe no cat maybe a res idk i dont think so tho. its a 97 and doesnt set off any check engine codes but the only headers performance thats made is 2.25, oh well tho im going to have to do it i already spent the money on the headers and cat and res and go...

Josh wrote:Look around for the 323. You may find something if you post on Club Protege. Apart from making your own I think that is about all you will find. :/

they have performance headers that will fit my car? even with minor modification thats fine as long as out downpipe outlet is 2.25

well i have yet to put it in BUT even corksport said that id need to remove the ac. i checked it out it really seems like it moved the position of the pipes going to the center more towards the center, but the 4 to 1 pipes spread and thats where it will be in the same location as the AC. well i plan...

okay so my ac system was never working and i took it out thats besides the point.... im going to put in some corksport headers and theyre the only ones that i can put to my b6 for me to install it i need to remove the ac condenser (which i have no problem) really what im wondering is if there is a m...

ive replaced all my gaskets i got them from ebay for pretty cheap, although ive had to go back and redo a lot of them. i just went to the mazda dealer to get it or the autoparts store. (the injector o rings were incorrect with the one i got so i had to get some at the autoparts store that worked per...

Yeah that is a little jacked up. I did not remember the sohc being like that. What I would do if I were you is just run one. I would run it on the PCV side. That is what is going to cause it to smoke. The other one you could probably block off if you wanted. But I would clean it all out with carb c...

i have another question about this. can i have two? one for the pvc line and one for the line that goes from the valve cover to the intake arm? the intake arm has some oil up in it so i figured two catch cans would be better then one lol if its a good idea im going to do it all when i replace my in...