|
Page 1 of 1
|
[ 3 posts ] |
|
Eunos 800 KL62 PCM (ECU) (ECM)
| Author |
Message |
|
JM1EC-V6
Regular Member
Joined: October 25 2005, 8:35 PM
Posts: 192
Location: Chicoutimi, Québec , Canada
|
 Eunos 800 KL62 PCM (ECU) (ECM) Hi, I am from Canada and doing a important engine conversion with a JDM Eunos 800 KL-ZE engine (TA5Z Chassis).
Just NEED A GOOD PERSON to find the ECU pinout and I.A.T. / M.A.F. wiring to run the motor.
Ecu P/N: KL62 18 881A
Vehicle: 1994 JDM Eunos 800 (1 ECT Sensor)
Engine: 2.5L DOHC KL-ZE 10:1 CR
Thanks !
_________________
'94 Mx-3 GS-R SE, KL-ZE Interprep. (From '96 PGT KL)
1110Kg
-Interprep KL31 Spec.
ported heads, Polished combustion chamber,3 angle vlv job,10.3:1 C.R.,0.020'' O.S.,KL31 cam,-0.007'' heads,Long neck IM,KL31 TB, Hotshot headers,2.25'' exhaust,Magnaflow cat
  
|
| January 15 2010, 8:11 PM |
 
|
|
|
fowljesse
Supporting Member
Joined: March 17 2006, 3:59 PM
Posts: 5676
Location: portland, OR
|
Re: Eunos 800 KL62 PCM (ECU) (ECM) I wish you luck. Those are hard to find. However, the K8 isn't too far off, and you can run the JE50 MAF. You can have most K8 ECUs reflashed.
_________________
'93 GS - P&P DE w/ ZE exh. cams/ pistns, KLG4 IM, 65mm TB, MSnS, Phenos, K&N RAI, UDP, Grnd wires, rear batt, filld MM, torq strt, TWM short shftr, Exedy, Lng tube hdrs 2.5" Side exhaust, H&R sprngs, Poly bushngs, strutbars, Alum. crss mmber&tiebar, 22mm swybar, solid links, Direzzas, leather int, Alpine 9805 stereo & alrm, keyless entry, 10 Boston Accoustics spkrs, Prjectrs, Blaster2, CF hood, FG hatch, Lexan
|
| January 15 2010, 11:06 PM |
|
|
|
Nd4SpdSe
Senior Member
Joined: May 25 2002, 2:01 AM
Posts: 11212
Location: CFB Val-Cartier, Quebec, Canada
|
Re: Eunos 800 KL62 PCM (ECU) (ECM) Here's just the 95 Millenia 2.5 wiring. Not sure if it'll help  
_________________
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
|
| January 23 2010, 12:58 PM |
|
|
|
|
|
Page 1 of 1
|
[ 3 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 1 guest |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
|
|
