Donate to the MX-3.com Forums
View unanswered posts | View active topics It is currently October 23 2019, 6:36 AM



Reply to topic  [ 236 posts ]  Go to page 1, 2, 3, 4, 5 ... 16  Next
 weede`s KL-ZE Supercharger - Megasquirt 
Author Message
Regular Member

Joined: August 07 2010, 11:03 AM
Posts: 155
Reply with quote
Post weede`s KL-ZE Supercharger - Megasquirt
Hello, My name is Jerry and I come from Poland ;)

Here is my 94` Mazda:

2015 SETUP

Engine:
2.5v6 KLZE engine (Full rebuild)
Oil filter relocation kit (custom)
KLZE straight-neck intake
Millenia-S injectors 280cc
Millenia-S Rods with ZE pistions (custom pins)
StandAlone Megasquirt II ECU
Eaton M62 Supercharger with custom bracket
AFR Innovate MTS with Gauge
FPR Turbosmart with custom adapter
MAP Sensor conversion
2,5" exhaust with twin-loop OBX mufler
2,5" ss headers
FMIC with custom aluminum piping

Gearbox
KL gearbox
Mazda KL LSD (torsen)
III straight cut gear PAR Engineering
ACT KL clutch kit w. 6pads
short-shifter

Brakes:
Mazda Xedos 9 brake pump with servo
Mazda 6 calipers with 283mm rotors
Goodridge steel lines
FERODO pads

Suspension
Tokico HP Struds
Ground Control Coilover Kit with Eibach springs
Eibach cambers
Poli-Brush red
Rear and front strud bars

Wheels
Dragwheels DR-23 Rally Bronze 16"
Yokohama AVS 205/50 tires
Dragwheels black screws

Interior
Sparco Torino II Seats with custom rails
323 GTR momo steering wheel
Oil temp, Oil Press, Intake pressure gauges
AFR Gauge Innovate
ALPINE CDE-101R

Image
Image
Image

_________________
My White JDM MX-3 ZE


Last edited by weede_klze on August 04 2015, 6:42 PM, edited 12 times in total.



August 07 2010, 11:59 AM
Profile
Senior Member
User avatar

Joined: October 16 2004, 2:01 AM
Posts: 6289
Location: British Columbia
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
O-M-G...

This has to be the best mx3 that I have seen for some time! Very clean and well modded. Wow :)


August 07 2010, 12:40 PM
Profile
Forum Moderator
User avatar

Joined: August 10 2005, 10:08 PM
Posts: 6128
Location: Hillsboro, OR
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
ditto - nice first post! Sweet mx-3 man, welcome to the forums!

_________________
My Feedback
92 mx-3 gs klze 'race car' IP 15.05 @ 92.5mph
92 mx-3 gs klze 'daily driver' IP 14.55 @ 95.7mph
http://www.cardomain.com/id/Mooneggs
Image


August 07 2010, 1:04 PM
Profile WWW
Regular Member
User avatar

Joined: August 21 2009, 5:24 PM
Posts: 1196
Location: Prattsburgh NY
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
Wow super nice and clean. Where are you located???

_________________
We all want to be fast and look cool. Cool changes but fast never does.


August 07 2010, 6:37 PM
Profile
Senior Member
User avatar

Joined: October 16 2004, 2:01 AM
Posts: 6289
Location: British Columbia
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
He's from poland by the looks of it


August 07 2010, 6:53 PM
Profile
Regular Member
User avatar

Joined: November 24 2008, 6:46 PM
Posts: 419
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
clean very clean

_________________
It only takes a single voice to start a revolution


August 07 2010, 8:32 PM
Profile
Regular Member

Joined: August 07 2010, 11:03 AM
Posts: 155
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
thank`s everyone ;)

I`m doing a research about force induction with a Eaton m62 like this:
Image

A plan is to have 250-270hp becouse after that it will be some problems with gearbox ;)

I`ve done a proper list to this modyfication:
- eaton m62 supercharge (i think 0,5bar it will be enough) - what belt will fit?
- mounting kit replace Air conditionf supercharge
- millenia s rods
- millenia s 270cc injectors (will it adequate to about 250hp?)
- slim ntercooler + piping
- smt6 or MS computer
- egt, oil temp. gauge (something else? afr?)
- walbro 255 fuel pomp
- ???

Maybe it will be my winter project if everting goes right ;)

_________________
My White JDM MX-3 ZE


August 07 2010, 9:20 PM
Profile
Senior Member
User avatar

Joined: October 16 2004, 2:01 AM
Posts: 6289
Location: British Columbia
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
weede_klze wrote:
- eaton m62 supercharge (i think 0,5bar it will be enough) - what belt will fit?


You will need to take a peice of string or tape and make a loop and get the measurement that way and get a custom belt.

weede_klze wrote:
- millenia s rods
- millenia s 270cc injectors (will it adequate to about 250hp?)


You dont need rods, the stock rods will hold as long as you have a good tune, that way you dont need to take apart your motor. Milly s injectors will work fine.

weede_klze wrote:
- egt, oil temp. gauge (something else? afr?)


Boost, AFR and EGT or oil press are most important.


August 07 2010, 10:39 PM
Profile
Regular Member

Joined: August 07 2010, 11:03 AM
Posts: 155
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
Thank`s! I`ll still doing some research about this.

KLZE + supercharge sounds insane!
http://www.youtube.com/watch?v=5PTrZJvA ... re=related

_________________
My White JDM MX-3 ZE


August 09 2010, 5:23 AM
Profile
Regular Member
User avatar

Joined: March 11 2010, 3:43 PM
Posts: 183
Location: British Columbia, Canada
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
Dude! Wow! So nice! 5*


August 09 2010, 2:10 PM
Profile
Regular Member
User avatar

Joined: April 19 2010, 1:12 AM
Posts: 391
Location: Edmonton,Alberta
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
Thats one sharp looking MX3.Love it in white.Keep it clean and stock looking. 8)


August 09 2010, 7:54 PM
Profile
Regular Member

Joined: August 07 2010, 11:03 AM
Posts: 155
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
I don`t like spoilers at all ;) only exception is mazdaspeed front bumper which is very very rare in europe and corcsport with shipping too expensive

_________________
My White JDM MX-3 ZE


August 10 2010, 3:55 AM
Profile
Regular Member
User avatar

Joined: August 21 2009, 5:24 PM
Posts: 1196
Location: Prattsburgh NY
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
This may be a long shot but I would be willing to look into shipping you a mazdaspeed for an oem like you have on your car (with a lip). :shrug: :shrug: :shrug: :shrug: Just a thought.

_________________
We all want to be fast and look cool. Cool changes but fast never does.


August 10 2010, 11:30 PM
Profile
Senior Member
User avatar

Joined: April 09 2007, 1:26 PM
Posts: 2400
Location: Calgary, AB
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
Does that sticker say SRT8????


August 11 2010, 12:00 AM
Profile
Senior Member
User avatar

Joined: December 30 2008, 4:41 AM
Posts: 2504
Location: Calgary, Alberta, Canada
Reply with quote
Post Re: 94" weede`s JDMstyle MX-3ZE
RS_OBD'oh_2 wrote:
Does that sticker say SRT8????

i was wondering when someone would mention that

_________________
Worklog: viewtopic.php?f=46&t=70628

Image


August 11 2010, 12:22 AM
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 236 posts ]  Go to page 1, 2, 3, 4, 5 ... 16  Next

Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.